User manual PANASONIC KX-TG8621E

[. . . ] TG862xE(e). book Page 1 Thursday, March 17, 2011 11:40 AM Operating Instructions Premium Digital Telephone with built in Answering System and TFT Colour Display Model No. KX-TG8621E KX-TG8622E KX-TG8623E Model shown is KX-TG8621. Before initial use, see "Getting Started" on page 10. Thank you for purchasing a Panasonic product. Please read these operating instructions before using the unit and save them for future reference. You must subscribe to the appropriate service offered by your service provider/telephone company. Please access our online customer survey: http://panasonic. net/pcc/tel/q TG862xE(e). book Page 2 Thursday, March 17, 2011 11:40 AM Table of Contents Introduction Model composition . [. . . ] Increase or decrease the sensitivity to adjust the sound level needed to trigger the baby monitor feature. L This feature cannot be set during a monitoring call. 1 2 3 Press 1 on the handset being monitored. {r}: "Sensitivity Level" s M Press {^} or {V} to select the desired setting. {r}: "On/Off" s M {r}: "Off" s M s {ic} Editing an outside monitoring number 1 2 3 4 5 Press 1 on the handset being monitored. {r}: "On/Off" s M {r}: "On" s M {r}: Select the outside line. s ~ 1 s {r}: "Edit" s M Note: L When the baby monitor is activated, you cannot access the direct commands using the monitored handset. Before setting the baby monitor feature, you can use direct commands to adjust baby monitor sensitivity (page 26). Helpline Tel. 0844 844 3898 Ireland 01289 8333 35 TG862xE(e). book Page 36 Thursday, March 17, 2011 11:40 AM Programming Answering the baby monitor When monitoring with a handset: Press {C} to answer calls. L The monitoring handset will answer calls automatically when the auto intercom feature is set to "On" (page 53). Note: L If you receive an outside call when communicating with the monitored handset, you hear 2 tones. When monitoring from an outside line: To answer a call, follow the operation for your phone. If you want to respond from the monitoring handset, press (1 using tone dialling. Note: L 2 minutes after the monitored handset starts a call, communication between the monitored handset and monitoring phone line is turned off automatically. Important: L The additional handset model recommended for use with this unit is noted on page 4. If another handset model is used, certain operations may not be available. Additional base units Handsets can be registered to up to 4 base units, allowing you to add additional base units and extend the area in which your handset(s) can be used. If a handset moves out of range of its base unit when "Auto" is selected on base unit (page 37), it looks for another base unit to make or receive calls. A base unit and the handsets it communicates with is called a "radio cell". Note: L Calls are disconnected when the handset moves from one radio cell to another. Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, _ is displayed even when the handset is near the base unit), reregister the handset. 1 Handset: 1 (middle soft key) (13) {r}: Select a base unit number. (No registration tone) L If all registered handsets start ringing, press {x} again to stop, then repeat this step. Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to a single base unit. 2 3 36 Helpline Tel. 0844 844 3898 Ireland 01289 8333 TG862xE(e). book Page 37 Thursday, March 17, 2011 11:40 AM Programming L The next step must be completed within 90 seconds. 2 3 {r}: Select the handset you want to cancel. {ic} 4 Handset: M s Wait until "Base PIN" is displayed. [. . . ] L Press {ic} on the handset to hang up. I cannot have a conversation using the headset. Noise is heard during a call on the headset. I cannot connect my headset to the handset. Your headset automatically connects to an outside line when turning it on. An error tone is heard when I try to program the Bluetooth feature. L The handset does not support enhanced features such as Last number redial or Call reject. L The bluetooth feature cannot be accessed immediately after turning on the handset. [. . . ]