User manual PANASONIC KX-HNS102FX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC KX-HNS102FX. We hope that this PANASONIC KX-HNS102FX user guide will be useful to you.


PANASONIC KX-HNS102FX : Download the complete user guide (574 Ko)

You may also download the following manuals related to this product:

   PANASONIC KXHNS102FX (612 ko)
   PANASONIC KXHNS102FX (602 ko)
   PANASONIC KXHNS102FX (593 ko)
   PANASONIC KXHNS102FX (569 ko)
   PANASONIC KX-HNS102FX (1230 ko)
   PANASONIC KX-HNS102FX (577 ko)
   PANASONIC KX-HNS102FX (888 ko)
   PANASONIC KX-HNS102FX (888 ko)

Manual abstract: user guide PANASONIC KX-HNS102FX

Detailed instructions for use are in the User's Guide.

[. . . ] Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R The system’s wireless features are subject to interference, therefore functionality in all situations cannot be guaranteed. Panasonic will not be held responsible for injury or damage to property that occurs in the event of wireless communication error or failure. devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. [. . . ] Note for the battery removal procedure Refer to “Inserting the batteries” on page 8. Other information CAUTION: Risk of explosion if battery is replaced by an incorrect type. Routine care R Wipe the outer surface of the product with a soft moist cloth. Disposal of Old Equipment and Batteries (Only for European Union and countries with recycling systems) 1 2 These symbols (A, B) on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection 6 Setup Part names and functions as possible, otherwise battery life may be reduced. Indicator Green, lit Red, lit Red, blinking Green, blinking slowly Off Status No motion detected Motion was detected Sensor is out of range of the hub Registration mode (You pressed and held M N) No battery power A B C D Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 8). E Infrared sensor LED indicator MHIGHN/MLOWN Used to change the sensor sensitivity (page 14). Rear cover M N Used to confirm the status of the sensor or register the sensor to the hub. Setup overview 1 Initial setup Make sure you can access the system using your mobile device. Registration Required only if the motion sensor was purchased separately (i. e. , not as part of a bundle). Confirm the installation area Read the information in this document to confirm that the desired installation area is suitable to proper operation. Installation Install the motion sensor in the desired location. 2 3 LED indicator N and check the You can press M LED indicator to confirm the sensor’s status. After confirming the sensor’s status, we recommend turning the LED indicator off by pressing M N again as soon 4 5 7 Setup Inserting the batteries R USE ONLY Alkaline batteries AA (LR6) size. R Place it with the “ ” mark facing upwards and slide it. 1 Remove the rear cover by pressing the upper sides of the cover (A) and sliding it down (B). A B 2 Insert the batteries. Registering the motion sensor This procedure is not required for devices that were included as part of a bundle. Before you can use the motion sensor, it must be registered to the hub. If you purchased devices separately (i. e. , not as part of a bundle), you must register each device to the hub. You can register each device by using the registration buttons or the [Home Network] app. 8 Setup Using registration buttons 1 Hub: motion sensor’s sensor features in these situations. R Panasonic takes no responsibility for any injury or damage caused by the use of the motion sensor. 2 Press and hold M OTHER DEVICEN until the LED indicator blinks slowly in green. Motion sensor: N until the Press and hold M LED indicator blinks slowly in green (page 7). R When registration is complete, the hub sounds one long beep. Using heat to detect motion The motion sensor’s infrared sensor can detect motion by recognizing temperature differences that occur within the range of the sensor. It does this by detecting the infrared rays that are emitted naturally by people, animals, etc. , which correlate to the object’s temperature. The detection range is indicated in the illustration by the grey area in front of the motion sensor. Detection range when looking from above Note: R To cancel without registering the sensor, press M N on the hub and on the sensor again. R If registration fails, the hub sounds several short beeps. Using the app When you register the motion sensor by using the [Home Network] app, you can assign a name to your devices and group them by location. [. . . ] 25 °C) R Dimensions (height ´ width ´ depth) – With the rear cover attached: Approx. 72 mm ´ 73 mm ´ 39 mm – With the wall mounting adaptor attached: Approx. 72 mm ´ 73 mm ´ 61 mm R Mass (weight) – With the rear cover attached: Approx. 70 g, excluding the batteries – With the wall mounting adaptor attached: Approx. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC KX-HNS102FX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC KX-HNS102FX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.