User manual PANASONIC CQ-DP383U SIRIUS
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC CQ-DP383U SIRIUS. We hope that this PANASONIC CQ-DP383U SIRIUS user guide will be useful to you.
Manual abstract: user guide PANASONIC CQ-DP383U SIRIUS
Detailed instructions for use are in the User's Guide.
[. . . ] This could cause electrical shorts, fire, or other damage.
Use Authorized Servicenters
Do not attempt to disassemble or adjust this precision product. Please refer to the Servicenter list including with this product for service assistance.
When Parked
Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on.
For Installation
This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30x.
Use the Proper Power Supply
This product is designed to operate with a 12 V DC, negative ground battery system.
Components
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation hardware. . . . . . . . . . . . . . . . 1 set ( page 28) Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ( page 15)
STD : Standard spectrum analyzer display (9 bands)
Contrast
Allows you to adjust the display contrasts for better viewing. SET #]/["] or [#] to select
[TUNE $]/[$]: level up [TUNE %]/[%]: level down Press [BAND] (SET) to set.
CONTRAST
Press [BAND] (SET) to set. SET #]/["] or [#] to select
AUDIO PICTURE
Clock on the Mode Display
Default: ON ("--:--" will appear before adjusting the clock. )
Press [BAND] (SET) to select ON OFF : Clock display ON : Clock display OFF
Clock display
FUNCTION
CLOCK-OFF CLOCK-ON
Press [P. SET #]/["] or [#] to select
Hour/Minute Switch [TUNE %]/[%]: The hour display high lights. [TUNE $]/[$]: The minutes display high lights.
Hour/Minute Adjustment [P. SET #]/[#]: Put back hour/minute.
Clock Adjustment
(12 hour system) Default: Not adjusted.
CLOCK ADJ
Press [BAND] (SET) to set.
Press [BAND] (SET) to set. CQ-DP383U SIRIUS
24
CQ-DP383U SIRIUS
25
E N G L I S H 17
User Settings
[MENU] [BAND] (SET)
REMOTE SET/AUTO·P ;/1
[DISP] Function menu display
CQ-DP383U SIRIUS
MOSFET
POWER
SOURCE
1
2
RAND
BAND
50WX4
OPEN
DISP
3
VOL
SCAN
4
REP
VOL
MENU
P·SET
CH·C !@
D·M
PWR
TUNE TRACK DISC
MUTE
S·HDB
SOURCE
5
6
MENU
DIM
HDB
CD RECEIVER WIITH FULL DOT MATRIX DISPLAY
[P. SET "] [P. SET #] (MENU SELECT)
["] [#] (MENU SELECT)
MUTE
SEL
BAND
[SEL] (MENU) [BAND] (SET) [DISP]
Notes: Operations except setting should be performed after returning to the mode display. The display returns to the previous one with no operation for 15 seconds after changing to the menu display. Press [DISP] to return to the regular mode.
E N G L I S H 18
DISP
Car Audio
1 Menu
Mute/Attenuator
You can select how much to lower the volume when [MUTE] is pressed. SET #]/["] or [#] to select
3 Setting
Press [BAND] (SET) to switch between MUTE (mute) or ATT (attenuator) in turn. : Decrease the volume to 1/10.
MUTE KEY
Excluding AUX-IN from Source Selection
Default: ON
Press [MENU]/ [SEL] (MENU) to select "FUNCTION" on the menu display. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN).
Connect All Leads
Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram ( pages 34j35) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis.
Required Tools
You'll need a screwdriver, a 1. 5 V AA battery, and the following: 12 V DC Electrical Side-cut Test bulb tape pliers
Overview
This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. Check the operation of the unit.
Dashboard Specifications
Thickness Min. [. . . ] Never try to repair the unit yourself because it is dangerous to do so.
Cautions: Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it.
E N G L I S H 28
Troubleshooting Tips
Common
Trouble Cause/Step Car's engine switch is not on. Turn your car's ignition switch to ACC or ON.
Extension cord (supplied for CX-DP88U/N)
Cables are not correctly connected. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC CQ-DP383U SIRIUS
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC CQ-DP383U SIRIUS will begin.