User manual PALM ULTRALIGHT WIRELESS HEADSET

[. . . ] User Guide Palm® Ultralight Wireless Headset Table of Contents Palm® Ultralight Wireless Headset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Charging your headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pairing your headset with your Bluetooth smartphone . . . . . . . . . . . . . . . . [. . . ] Hold the ear tip with the elongated edge pointing down, and push the post into the opening on your headset. This is the neutral position. Palm® ultralight wireless headset 11 Wearing your headset on your left or right ear 3 With the ear tip facing you, twist the tip toward the R for right-ear wearing or toward the L for left-ear wearing. Neutral position Right ear Left ear 4 To remove the ear tip, make sure it's in the neutral position and then pull it away from your headset. 12 Palm® ultralight wireless headset Wearing your headset on your left or right ear 0 [ * ] NOTE For optimal performance, wear your headset and your Bluetooth phone on the same side of your body. In general, you will get better performance when there are no obstructions (including parts of your body) between your headset and the phone. When the connection drops between the devices, you will hear a beep in your headset. When you go out of range, only the power off function will operate. Using the earloop You can attach the earloop to your headset to improve stability. 0 1 Remove the ear tip from your headset by turning it to the neutral position and pulling it away from your headset. Palm® ultralight wireless headset 13 Wearing your headset on your left or right ear 2 Attach the earloop between your headset and the ear tip, and replace the ear tip. For the right ear, the earloop appears as shown in the following figure. The ear tip should rest against, but not enter, the ear canal. This earloop is positioned to fit over the right ear. 14 Palm® ultralight wireless headset Using your headset Using your headset Your headset uses a digital signal processor (DSP) to reduce background noise. For other phones, you may need to press and release the Call control button to transfer the call to your headset. 3 Increase or decrease the call volume by pressing the top or the bottom of the Volume button . The volume of the confirmation tone you hear increases or decreases to match the call volume. Palm® ultralight wireless headset 17 Using auto answer 4 To end the call, press and release the Call control button, or use the controls on your smartphone to end the call. ] IMPORTANT Use only short presses when ending or answering a call to avoid accidentally activating your headset's Advanced features. If you miss a call, the indicator light on your headset flashes blue and purple every six seconds to alert you about the missed call. [ * ] NOTE When your headset has been paired with your phone and you make or answer a call on your phone while your headset is turned off (or is out of range of the phone), your headset automatically tries to connect to the call if you turn it on (or bring it back into range of your phone). If your headset does not automatically connect to the call in this case, quickly press the Call control button to connect. Using auto answer If your headset is in the headset carrying pocket when it receives a call, the carrying pocket vibrates. · Remove your headset from the headset carrying pocket to automatically answer the call. · Return your headset to the headset carrying pocket to end the call. 18 Palm® ultralight wireless headset Muting a call Muting a call To mute your voice while on a call, press both sides of the Volume button at the same time until you hear two ascending tones. While the mute feature is active, you hear two tones every 60 seconds. To turn off the mute feature, press both sides of the Volume button again. Palm® ultralight wireless headset 19 What do the colored flashes and tones mean? What do the colored flashes and tones mean? 0 Headset status Powering on Colored flashes and tones Blue flash followed after a few seconds by 1-3 red flashes indicating the battery level. Blue flash every 5 seconds Red flash and descending tones No lights Long blue flash every 10 seconds Blue flash every 10 seconds and 2 tones sound every 60 seconds Constant red light Red light turns off Red flash every second and 2 tones sound every 20 seconds Alternating blue and red flashes Rapid, alternating blue and purple flashes every 6 seconds Rapid, alternating blue and red flashes Power on Powering off Power off On a call Mute on Charging battery Battery fully charged Low battery Pairing mode Missed call Ringing 20 Palm® ultralight wireless headset Advanced features Advanced features Advanced features are available for smartphones that support the hands-free Bluetooth profile; this means you can use your headset instead of your smartphone to perform other tasks like redialing and putting a call on hold. Check your smartphone's instruction guide or contact the manufacturer if you are not sure if your smartphone supports the hands-free Bluetooth profile. [ * ] NOTE Most Bluetooth phones support the hands-free profile. Ignore an incoming call When your phone rings, press the Call control button for one second to ignore the call. Redial the last number To redial the last number you called, quickly press the Call control button twice. Switch a call from phone to headset To switch a call from your phone to your headset, briefly press the Call control button. [. . . ] Southpoint, Building C Scorpius 140 2132 LR Hoofddorp The Netherlands Tel. +31 23 5648015 www. plantronics. com Declaration of Conformity In accordance with EN45014: 1998 We, Plantronics BV, declare under our sole responsibility that the following products comply with the essential requirements and other relevant provisions of the Radio and Telecommunications Terminal Equipment Directive 1999/5/EC. Product Name: Manufactured by: Address of Manufacturer: Palm® Ultralight Wireless Headset - 3265WW Plantronics BV Southpoint, Building C Scorpius 140 2132 LR Hoofddorp The Netherlands This Product conforms to the following European standards. 1999/5/EC reference Article 3. 1 a - Safety Article 3. 1 b - Electromagnetic Compatibility Article 3. 2 - Radio Spectrum Use Standard EN 60950-1: 2001 +A11 EN 50360: 2001 EN 50371: 2002 EN 301 489-01: V1. 5. 1 (2002-08) EN 301 489-17 V1. 2. 1 (2002-08) EN 300 328 V1. 6. 1 (2003-04) Signed____________________ Steven F Burson Date March 10, 2006 Vice President, Product Development and Technology This Declaration of Conformity is based on the evidence contained in: Plantronics CE Marking Verification Report: CEMVR_327-02. Declaration of Conformity Number: DOC_355B. doc Chamber of Commerce Amsterdam Registration Number: 34277402 28 Palm® ultralight wireless headset Product regulatory information Approval marks 0 CE mark AT, BE, DE, DK, ES, FR, GB, GR, IT, IE, LU, NL, PT, SE, FI, CY, CZ, EE, HU, LV, LT, MT, PL, SK, SI 0 Mexico approval mark Australia/New Zealand approval mark 0 For information on Palm's environmental programs, visit www. palm. com/environment. Static Electricity, ESD, and Your Palm Device Electrostatic discharge (ESD) can cause damage to electronic devices if discharged into the device, so you should take steps to avoid such an occurrence. Description of ESD Static electricity is an electrical charge caused by the buildup of excess electrons on the surface of a material. [. . . ]