User manual PALM CONNECTIVITY KIT

[. . . ] 5 Replacing batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Configuring your computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Configuring your handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Installing applications on your handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Tip: To add a "pause" in the dialing sequence, enter a comma in the field. If the phone line you're using for the handheld has Call Waiting, select the Disable call waiting check box to avoid an interruption during the modem HotSync operation. If you want to use a calling card to place the call, select the check box and enter the calling card number. Tap OK. To select Connection Preferences for a modem HotSync operation: 1. Tap the configuration you want to use. Page 8 Setting Up Your PalmModem® Connectivity Kit 5. Adjust the other options as needed. Dialing Select the Rotary setting only if you are certain that your telephone service does not support TouchTone dialing. Note: When dialing from Europe, the modem supports TouchTone dialing only. Rotary and pulse dialing are not supported in Europe. Volume Controls the modem speaker volume. Chapter 2 Page 9 Details Provides access to the following optional settings: s Speed. If your modem receives more data than its buffer can hold, the modem uses flow control to temporarily stop data transmission. s Init String. This field is used for standard AT commands that enable the modem to perform special functions. 9. Tap OK to save the settings. To prepare your handheld for a network HotSync operation: 1. Tap Select Service. Page 10 Setting Up Your PalmModem® Connectivity Kit Tap here Note: See "Network preferences and TCP/IP software" in your handheld handbook for information on creating a network connection. Note: Before performing a network HotSync operation, you must enable the network HotSync technology and perform a local HotSync operation. Contact your System Administrator to set up the network HotSync technology, and for additional information, go to this web site: http://www. palm. com. Selecting conduits for a modem HotSync operation The Conduit Setup dialog box on your handheld enables you to define which files and/or applications synchronize during a modem HotSync operation. You can use these settings to minimize the time required to synchronize data with a modem. Chapter 2 Page 11 To change conduits for a modem HotSync operation: 1. Tap the check boxes to deselect the files and applications that you do not want to synchronize during a modem HotSync operation. The default setting is to synchronize all files. Note: Applications that do not have a database (such as games) do not synchronize -- even if you select the item in the Conduit Setup dialog box. If you accidentally use a digital phone line, your modem will respond as though there is no dial tone. Performing a remote HotSync operation After you connect your modem to your handheld, you can use your modem to perform remote HotSync operations by dialing your PC modem or network server. Important: Remember to leave your computer running so you can perform remote operations. To perform a modem or network HotSync operation: s Press the HotSync button on the front of your modem to initiate remote HotSync operations. If you have any problems conducting a successful HotSync operation, see "Frequently Asked Questions" in your handheld handbook. Page 16 Using Your PalmModem® Connectivity Kit Detaching your PalmModem connectivity kit After you complete your modem operations, press the buttons on both sides of the modem, then rotate the handheld away from the modem. Press buttons Pull handheld from modem Chapter 3 Page 17 Page 18 Using Your PalmModem® Connectivity Kit Product Regulatory Information FCC-15 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. [. . . ]