User manual PACKARD BELL VISEO 190

[. . . ] ANT IN Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the product. Make sure to use a TV antenna cable (sold separately) as the antenna cable. S-Video/Video/R - AUDIO L, S-Video / Video Input devices such as DVD, VCR or Camcorder are connected to the VIDEO or S-VIDEO terminal of the monitor using the Video or S-Video cable. R - AUDIO - L Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor. Connect your headphones to the Headphone connection terminal. Kensington Lock Introduction The Kensington Lock is a device used to physically fix the system when using it in a public place. [. . . ] Make sure to use a TV antenna cable (sold separately) as the antenna cable. · When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. · When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. · To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. 2. Purchase and install a signal amplifier for better reception. Connecting DVD / DTV Set Top Box Note Connect to the DVD / DTV Set Top Box input if the device has a [COMPONENT IN] connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. Connections Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the monitor. Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the [PR, PB, Y] input ports using a component video cable (PR, PB, Y). Note Select "Component" using the 'SOURCE [ ]' If you connect the PR, PB, and Y component cables to the incorrect terminals, the screen will be displayed in red or blue. For single-family houses, install an UHF antenna to receive digital broadcasting. Connecting HDMI Note You can connect digital output devices to your monitor. Connecting Using a HDMI Cable Input devices such as digital DVD are connected to the [HDMI IN] terminal of the monitor using the HDMI cable. When all the connections are completed, connect the power cords for the monitor and DVD(or the device connected to the digital output terminal). Q: A: Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on. (Refer to the Connecting the monitor) "Check Signal Cable" message Ensure that the signal cable is firmly connected to the PC or video SOURCEs. (Refer to the Connecting the monitor) Ensure that the PC or video SOURCEs are turned on. "Not Optimum Mode" message Check the maximum resolution and the frequency of the video adapter. Check if the signal cable is securely connected. Connect it again securely. Turn on again after removing all accessories (video extension cable, etc. ) Set resolution and frequency to the recommended ranges. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor. If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. The image is too light or too dark Adjust the Brightness and Contrast. (Refer to the Brightness, Contrast) The Power Indicator blinks. Q: A: A: Q: A: A: Q: A: Q: A: A: A: Q: Q: A: Q: Troubleshooting A: Q: A: A: Q: A: The monitor is currently saving the changes made in settings to the OSD memory. The screen is blank and the power indicator light blinks every 0. 5 or 1 seconds. If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between the monitor and the computer to ensure that the connector is properly connected. 3. Problems related to Audio Note Problems related to audio signals and their solutions are listed below. Q: A: No sound Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card. (Refer to the Connecting the monitor) Check the volume level. (Refer to the Volume) The sound level is too low. Check the volume level. (Refer to the Volume) If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. A: Q: A: A: 4. [. . . ] SDTV (Standard Definition TV): Common standard digital TV. Troubleshooting A: An SDTV has an aspect ratio of 4:3 which is the same as that of an analog TV. Digital TV broadcasting in our country is ultimately orientated towards HDTV. You can receive all digital broadcasts, whether they are SD or HD, using any digital TV. However, you cannot enjoy HD programs, which are the highest quality digital TV programs, using an SD digital TV. [. . . ]