User manual OZ-VISION V4000

[. . . ] V4000 Remote Video System Control Center Guide Installer Version V4000 Control Center User Guide 1 CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Defining Screen Resolution and Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A red/white/blue frame will appear. Resize and move this frame by using the mouse Right click inside the frame to set the View Port. The frame will turn red and white only and the unit will send updates only in the marked area. To disable View Port, right click in the frame then click the left click outside the frame and right click again anywhere. V4000 Control Center User Guide 18 Setting Remote Unit Parameters A few seconds after pressing the tuning button in the control center, the remote setup window will appear. You can temporarily set the image resolution. (High-resolution delivers sharper images, with greater detail but slows the transmission rate). The resolution changes made here are temporary and the default parameters will be loaded on the next communication To set, update or change the remote unit's parameters, click on the Unit Power-on Parameters button. To upgrade the remote system's firmware directly from your PC via the phone, click Upload Firmware, which opens the upload window. · After the transfer, you will be disconnected from Enter the new password, confirm it and click Ok Temporarily sets the system mode to Black & White or Color video. Press Ok to confirm. The Set Remote Password button allows you to set or change the remote password. V4000 Control Center User Guide 19 Remote units parameters are divided into six tabs: General Parameters Every remote unit has a unique ID number. This identification number will appear in the ID and unit version fields. These parameters cannot be changed. · Alarm Phone Num #1 / #2 ­ Use these fields to enter the phone numbers that the unit will call in case of an alarm or a callback request. If you have only one phone line, type the same phone number in both fields. · Quality ­ Sets the compression ratio to the image quality you require. · Resolution ­ Sets the resolution to the quality you require. Remember high-resolution provides sharper images and greater detail but slows down the frame rate. · Black & White or Color- Selects black and white or color options. · Upload ­ Click this button to update the unit with the new parameters. · Save to file ­ Click this button to save the new parameters to a local file in your PC. · Close ­ Click this button to close the window without saving. V4000 Control Center User Guide 20 Advanced Parameters · Day-Night Switch Key Mode - Arm the unit only by key switch connected to the unit (toggle or push to change). · Circular Buffer Length ­ The length of the memory allocated to the pre/post alarm. · Pre-Alarm Length ­ The time span of the circular buffer allocated for pre-alarm frames. During a session triggered by an alarm, the unit will first transmit the pre-alarm frames, then the post-alarm frames, and finally, live video from the site. · Reference Update Threshold ­ Defines the amount of change in the video that will cause the unit to stop transmitting the streaming video, transmit a new reference, and then continue to transmit the streaming video. · Number of Connection Attempts ­Sets the number of tries the unit will call the Control Center if the computer does not answer or the line is busy. · Save Circular Buffer for ­ Number of minutes that the unit will save the frames stored as a result of an alarm. [. . . ] 5. V4000 Control Center User Guide 40 6. Set the speed of the Dome camera. If using a dry connect controlled motor, check the Implement Pan Tilt Zoom check box. Sweep Mode, Resolution and Quality settings determine the frame rate and quality during Dome camera movement. 7. 8. Type the ID number of the Dome camera in this box. (The Dome ID should be one to three digits. ) Click Ok to save the new parameters. [. . . ]