User manual OUTBACK POWER SYSTEMS MATE3

[. . . ] MATE3 System Display and Controller Owner's Manual About OutBack Power Technologies OutBack Power Technologies is a leader in advanced energy conversion technology. Our products include true sine wave inverter/chargers, maximum power point tracking charge controllers, and system communication components, as well as circuit breakers, accessories, and assembled systems. Contact Information Telephone: +1. 360. 435. 6030 (North America) +1. 360. 618. 4363 (Technical Support) +1. 360. 435. 6019 (Fax) North America 19009 62nd Avenue NE Arlington, WA 98223 USA Support@outbackpower. com www. outbackpower. com +34. 93. 654. 9568 (Barcelona, Spain) Address: E-mail: Web Site: Disclaimer UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER TECHNOLOGIES: (a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION. (b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER'S RISK. Warranty Summary OutBack Power Technologies Inc. [. . . ] Transfer Delay: Sets the duration that the input AC voltage or frequency may exceed limits before the inverter disconnects itself. This may be preceded by a warning (see page 39), and may be followed by a Last AC Disconnect message (see page 54. ) Connect Delay: Sets the designated delay period before the inverter begins accepting power from the generator. It is not the same as the warmup period used by the AGS function (see page 115. ) 80 900-0117-01-00 Rev A Inverter Settings AC Output This menu adjusts the output voltage produced while the inverter is inverting (running on battery power). This setting does not affect the output when using another AC input source. (See pages 79 and 80. ) The range of adjustability will vary with inverter model. See the inverter Operator's Manual for the specific range of adjustability. Press the button in the center of the control wheel to accept the selection. Use the control wheel to increase or decrease the set point to the correct voltage. Press the button in the center of the control wheel to accept the selection. After setting the parameters for each set point, press the TOP navigation key to return to the Main Menu screen. Figure 76 Set Points: AC Output Output Voltage: Adjusts the inverter's output voltage while in inverting mode. 900-0117-01-00 Rev A 81 Inverter Settings Low Battery While inverting, the inverter will not be able to sustain its operation if the battery voltage goes below a certain point. (See Figure 134 on page 139 for reviewing event details. ) This function, Low Battery Cut-Out, is often referred to as LBCO. The function is intended to protect the the batteries, as excessive discharge may damage a battery. Continuing to invert on a low DC voltage may produce a distorted waveform. See the inverter Operator's Manual for the specific range of adjustability. The inverter will also stop functioning and give an error due to high battery voltage. Press the button in the center of the control wheel to accept the selection. Use the control wheel to increase or decrease the set points to the correct voltage. Press the button in the center of the control wheel to accept the selection. This should automatically move the highlighting to the next set point. After setting the parameters for each set point, press the TOP navigation key to return to the Main Menu screen. Figure 77 Set Points: Low Battery Cut-Out Voltage: Sets the voltage at which the inverter shuts off due to a low-battery condition. If the batteries drop to this voltage for five consecutive minutes, the inverter will stop functioning. The MATE3 will display an event, with a Low Battery V error appearing in the Inverter Errors menu. [. . . ] 37, 38, 39, 40 Inverter Graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Sell Graph. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Software Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Mechanical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 M Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 MATE Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Soft Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 MATE3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 AGS Load Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]