User manual OREGON SCIENTIFIC WD338

[. . . ] STANDARD FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 1. 8 1. 9 KEY OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 THE BASE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 THE BASE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The base [CHARGE] light will come on to indicate the charging of handset. Always put the handset in the base cradle with the keypad facing outwards. will look like this Your handset is now ready for making and receiving calls. Replacing the handset batteries If you have been using your handset and find that you can no longer recharge the batteries, they may need to be replaced. The same kind of batteries as supplied in this product should be used. Remove the battery compartment cover by sliding it in the direction shown by the arrow. Close the battery compartment cover and secure its screw. 1. 6 Before you start Out of range warning If your handset is out of range of the base unit, there is a beep sound to alert you, and the display will show: If so, please move closer to the base unit until the handset display stops flashing. If you want to disable this tone, please refer to the section "Tone andVolume". Important: Due to radio interference in the environment, occasional loss of synchronisation between the handset and base may occur for a very short duration. The base will very quickly change to another channel automatically to overcome the interference and restore the synchronization. 10 Electrical safety * Do not install the base unit near a sink, bath or shower, or anywhere else where it could get wet. Electrical equipment can cause serious injury if used while you are wet or standing in water. If the base unit ever falls into water, Do not retrieve it until you have unplugged the power lead from the mains and the telephone line plug from the telephone socket; then pull it out by the unplugged cables. Never use your weather phone in the open air during a thunderstorm - unplug the base unit from the telephone line and the main socket when there are storms in your area. < & _ C F I L O R V Y , > % a d g j m S t Z ; [ / = b e h k n p u w : ] \ ^ c f i l o q v x ?) 2 s z { 7 9 } Note: takes you back to the previous character. character. goes to the next 13 To make a call to a stored number 1. Press to check the to begin a call. To clear a number from the memory 1. The handset display shows "deleted" or and select the required entry to select "Delete Entry" to select "Phonebook" To modify a number from the memory 1. The handset display shows "stored" 14 or and select the name to select "Edit Entry" to select "Phonebook" 1. 9 Caller display If you have subscribed to this service from your phone network operator, the caller's phone number will be shown on the handset display when there is an incoming call. The phone can store the caller ID's of up to 10 different call numbers. Note: If the caller's phone number was stored in the phone book, the associated name will be displayed with the phone number. Each entry in the caller list has: * * * * Caller number (up to 20 digits) The caller name (up to 8 characters) if this is stored in the phonebook or supplied from the telephone network. [. . . ] * * * * * First establish the call with the external party by either making an external call or answering an incoming call Press to make an intercom call to another handset The internal party answers your intercom call by pressing Then you press and hold for about 2 seconds (you will hear a confirmation key tone) Then the external party, another internal party and you can talk together 2. 4 Monitor Mode (Baby sit) This function is similar to intercom. It allows you to call the second handset automatically by internal call. If it is already set in monitor mode, you can listen to what is happening in another room by using the second handset like a microphone. To set the second handset to monitor mode: * * * * * * On the second handset, press Press repeatedly to select "Monitor Mode" Press Select Monitor Mode "On" The handset display will show "Monitor Mode" Now, when you call the second handset from the first handset, the second handset will automatically answer and you will be in Monitor Mode. [. . . ]