User manual OREGON SCIENTIFIC RMR616HGA

[. . . ] 7 Search for Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2. Insert the batteries, matching the polarity as shown in the battery compartment. If you are using more than one sensor, select a different channel for each sensor. For best results: · Insert the batteries and select the channel and temperature unit before you mount the sensor. · Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. You may need to experiment with various locations to get the best results. NOTE To maximise Atomic Clock signal reception, the main unit table stand should be fully opened until it locks into place. The reception icon shown in the Temperature and Humidity Areas show the status. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the Search for Sensor section for more information. ) Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. 4. 5. RMR616HGA lab test R2 7 1/17/04, 5:03 PM EN EN ICON DESCRIPTION Main unit is searching for sensors. Channel 1 is selected (number will change depending on the sensor you select) CLOCK This product can track the date and time for up to 2 locations (Clock with Offset Hour). The US Atomic Clock in Boulder, Colorado automatically updates this information unless you disable the feature. The signals are collected by the main unit when it is within 1500 km (932 miles) of a signal. Initial reception takes 2 - 10 minutes, and is initiated when you first setup the unit, and whenever you press RESET. The icon is shown in the Clock Area. --- shows in Temp / Humidity Areas The selected sensor cannot be found. Search for the sensor or check batteries. SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. [. . . ] · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. DECLARATION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www. oregonscientific. com, or on the warranty card for this product) for all inquiries instead. We Name: Address: Telephone No. : Fax No. : declare that the product Product No. : Product Name: Manufacturer: Address: Oregon Scientific, Inc. [. . . ]