User manual OREGON SCIENTIFIC RMR603HGA

[. . . ] 8 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Set Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Humidity Area when the OUTDOOR humidity is shown. CHANGE SETTINGS 1. Press MODE to confirm. TABLE STAND OR WALL MOUNT Insert the stand on the back of the product, or mount it on a wall with a nail. Remote REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo/ Hygro Sensor that collects Temperature and Humidity data. Additional sensors sold separately. 6 RMR603HGA lab test R2 6 1/17/04, 4:52 PM SETUP SENSOR Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity as shown in the battery compartment. If you are using more than one sensor, select a different channel for each sensor. For best results: · Insert the batteries and select the channel and temperature unit before you mount the sensor. · Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. You may need to experiment with various locations to get the best results. SWITCH Channel 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the Sensor Data Transmission section for more information. ) Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. 4. 5. 7 RMR603HGA lab test R2 7 1/17/04, 4:52 PM EN EN DATA TRANSMISSION Data is sent from the sensor(s) every 40 seconds. The reception icon shown in the Temperature and Humidity Areas shows the status. Channel 1 is selected (number will change depending on the sensor you select) The selected sensor cannot be found. Search for the sensor or check batteries. CLOCK This product shows the current time, time zone, and day of week in English, Spanish, or French. The time is automatically updated by the US Atomic Clock in Boulder, Colorado unless you disable this feature. Signals are collected by the main unit when it is within 1500 km (932 miles) of a signal. Initial reception takes 2 - 10 minutes, and is initiated when you first setup the unit, and whenever you press RESET. The icon is shown in the Clock Area. --- shows in Temp / Humidity Areas SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL for 2 seconds. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. 14 RMR603HGA lab test R2 14 1/17/04, 4:52 PM DECLARATION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www. oregonscientific. com, or on the warranty card for this product) for all inquiries instead. [. . . ]