User manual OREGON SCIENTIFIC RMR602A

[. . . ] 6 Setup Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Search for Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Only one sensor can be used with this product. 6 RMR602A lab test R2 6 1/17/04, 4:49 PM SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity as shown in the battery compartment. Press RESET, then SEARCH, on the main unit to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the Sensor Data Transmission section for more information. ) Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. For best results: · Insert the batteries before you mount the sensor. · Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. You may need to experiment with various locations to get the best results. 4. 5. 7 RMR602A lab test R2 7 1/17/04, 4:49 PM EN EN DATA TRANSMISSION Data is sent from the sensor(s) every 78 seconds. The reception icon shown in the Outdoor Temperature Area shows the status. Search for the sensor or check batteries. CLOCK This product has two displays: Clock with day of week in German, English, French, Italian, or Spanish, and Calendar display with month and date. The time is automatically updated by the US Atomic Clock in Boulder, Colorado unless you disable this feature. Signals are collected by the main unit when it is within 1500 km (932 miles) of a signal. Initial reception takes 2 - 10 minutes, and is initiated when you first setup the unit, and whenever you press RESET. The icon is shown in the Clock Area. --- shows SEARCH FOR SENSOR To search for the sensor, press SEARCH . NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. To force a manual search for Atomic Clock signals, press and hold UP for 2 seconds. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. 13 RMR602A lab test R2 13 1/17/04, 4:49 PM EN EN DECLARATION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www. oregonscientific. com, or on the warranty card for this product) for all inquiries instead. [. . . ]