User manual OREGON SCIENTIFIC RM318PU

[. . . ] Touching the ON/OFF button one time will either turn the alarm on or off. Please refer to the Alarm Setting instructions for further information. NOTE : When setting the alarm time, the alarm is automatically turned on. Touching the ON/OFF button one time will either turn the Alarm function on or off. [. . . ] It usually takes about 3-7 minutes for the clock to receive the initial Radio Signal and adjust the time, date and day accordingly. Due to possible interference, the best reception often occurs between midnight and 4 a. m. The clock not only sets itself to synchronize its digital time and date with the Atomic clock's signals, but it also automatically adjusts for daylight-savings time!Your clock utilizes a small internal antenna that double as the bedside/desktop stand. (Please see the section on "Signal Strength" for optimal performance of your Kids Projection Clock) The successful reception of the long wave signal depends on the positioning and location of the clock. Insufficient signal strength or external electrical noises may prevent the unit from receiving a complete signal. The main reasons for poor reception are heavily reinforced concrete and steel structures, and close proximity to electrical units such as TV's and PC monitors. RESET MODE / SET (Figure A. 5) Press the MODE key once to switch between the display of either the Day of the Week or Seconds on the clock. Kids Projection Clock will continue to display the selected function (Day or Seconds) until the MODE button id pressed again. IMPORTANT : Holding the MODE key for more than three seconds turns on the manual mode for setting the time, date, year and language (English/French/ Spanish). Please refer to this section for specific setting instructions. (( · )) / 24hOFF (Figure A. 6) Press the (( · )) key once to show the alarm time. The (( · )) /24hOFF icon is displayed in the lower left portion of the screen to alert you that the display is showing the alarm time. The "Minutes" segment of the clock time will begin flashing. TROUBLE SHOOTING Problem No Display · · Remedy Check battery compartment. Confirm that batteries are of good quality, and are installed correctly (( · )) Alarm Display indicator (Figure A. 12) This (( · )) icon indicates the second line of the display is showing Alarm Time. 4) While the "Minutes" segment is flashing press the [ desired minutes time. ] button to set the 5) When the desired minutes time is reached, briefly press the MODE button five more times to exit the clock time set mode. · [ ] Alarm " ON " Indicator (Figure A. 13) ] icon indicates that the alarm function is activated. This Bell [ IMPORTANT : As soon as any manual change in the clock time is mode, there is a loss of the signal strength indicator from the display. NOTE : The next sucessful reception of a radio signal will override a manually set clock time showing the clock running manually. Did not receive A time signal If the units are new and just out of the box, allow60- 72 hours cycle for the clock to automatically seek a signal between midnight and 4 a. m. Be certain the antenna cord is fully extended and look for low battery indicator. · [ ] Low Battery Indicator (Figure A. 14) This [ ] icon indicates that it is time to change batteries. Please refer to the Battery Replacement Section of this manual. Setting the Year 1) Press and hold MODE button for at least three seconds. The "Hour" segment of the clock time will begin flashing 2) Briefly press the MODE button and the "Minutes" segment will begin flashing. 4) While the "Year" segment is flashing press the [ sired year. ] button to set the de · USING THE PROJECTION CLOCK Projection Clock with Battery Power Only To activate the projection feature: · Press the Snooze button · · May be caused by interference. The ExactSetTM is equipped with a high quality clock mechanism, which insures accuracy between signals. Loss of Signal The projection light will illuminate for five seconds and then turn off automatically. Note: There is no option for continual display of the red projection beam with battery only power. If the projection light ON switch is in the "on" position in battery only mode, the projection beam is disabled. 5) When the desired year is reached briefly press the MODE button four more times to exit the year set mode. [. . . ] Press button until the desired month appears on the display Backlight To activate the backlight which will illuminate the LCD panel: · Press the Snooze button - the backlight will activate for 5 seconds, and turn off automatically Press Mode button three more times to exit the set mode and resume normal time keeping. BATTERY INSTALLATION (Figure B) To activate the unit simply slide the battery compartment door in the direction of the arrow. Insert the batteries strictly according to the polarities shown therein. NOTE : Please do not become alarmed if the unit does mot receive signal directly from the box. The unit will receive most dependable and interference free signal automatically between Midnight and 4 a. m. [. . . ]