User manual OREGON SCIENTIFIC PE826

[. . . ] 7 View Daily Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Clear All Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Clock / User Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 To Set the User Profile for 1st Time Use or After a Battery Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When target walk is complete, FINISH will appear and a beep will sound. 2. Press / to change the value of each digit, and SET to confirm and move on to the next setting. Once the target has been set, start walking to activate the pedometer. screen will appear to confirm that the unit is starting to monitor your progress. To reset the target for the next user session, press and hold RESET. TIMER When the timer is running, it will measure steps, distance and calories. These measurements are not linked to the daily measurements and are only related to the time spent walking while the timer is on. If the countdown timer is selected you will need to set the hr:min:sec by pressing / to change a value and SET to confirm. To use timer: · · · Press to start / stop the timer. When you are in the timer display you are in another mode, is running. If will flash to indicate the timer to toggle between the total weekly step, 2. When you have selected the day you wish to view a 1-second display will show to advise you if you reached that days target or not: · Target achieved = smiley face and high beep sound. · MEMORY The pedometer has a 7-day memory function. You can view total weekly or daily step, distance and calorie records. Target not achieved = sad face and low beep sound. VIEW TOTAL WEEKLY RECORDS 1. Press to toggle between your chosen days step, distance and calorie display. IMPORTANT At midnight all accumulated daily data will be stored for a period of 7 days. Therefore, once a memory has been stored for 7 days it is replaced with new data from the 1st day of the new week. 7 PE82X_M_EN_V2. p65 7 2005. 7. 19, 12:17 PM EN EN The bar at the bottom of the display will indicate which day's memory record you are looking at. CLEAR ALL RECORDS Press and hold RESET. CLOCK · 12/24hr format · Hour · Minute · Day of the week USER PROFILE · Upper pulse limit (PE826 only) · Lower pulse limit (PE826 only) · Weight unit · Weight · Stride unit · Stride · Age · Gender To calculate stride length: Individual stride length varies. To determine the average stride length, walk 10 paces and divide the distance traveled by 10. CLOCK / USER PROFILE TO SET THE USER PROFILE FOR 1ST TIME USE OR AFTER A BATTERY CHANGE When the installation tape is removed to activate the pedometer and whenever the batteries are changed, the pedometer will ask you to set the clock and user profile. Please complete the settings as shown below or your pedometer will not work properly. Press / to change a value and SET to confirm and move on to the next setting. The setting sequence is: 8 PE82X_M_EN_V2. p65 8 2005. 7. 19, 12:17 PM CHANGE INDIVIDUAL CLOCK OR USER PROFILE SETTINGS If after the initial setting of the clock / user profile (as detailed in previous section), you wish to change the clock time or edit one of the user profile settings, simply: 1. The setting sequence is: · Hour · Minute · On / Off To stop the alarm sound, press any key PULSE METER / STRESS INDEX (AVAILABLE IN PE826 ONLY) For first-time use, or after replacing a battery or resetting the unit, user must calibrate stress index baseline, otherwise no valid reading can be obtained. To calibrate your stress index baseline: The index is highly individual, so you need to calibrate your personal baseline before you use this function to monitor your stress status. Make sure you relax for 2 to 3 minutes before you start the calibration: 1. [. . . ] 13 PE82X_M_EN_V2. p65 13 · · 2005. 7. 19, 12:17 PM EN EN Do not use rechargeable batteries with this product. Remove the batteries if storing this product for a long period of time. The contents of this user manual and technical specifications are subject to change without further notice. Images not drawn to scale. · · Dimensions ­ without clip (W x H x D) and weight PE823 2. 1 x 1. 9 x 1. 0 inches (52 x 47 x 25 mm) 33 g (1. 16 ounces) 2. 4 x 2. 2 x 1. 0 inches (60. 3 x 54. 9 x 24 mm) 38 g (1. 34 ounces) 2. 3 x 2. 5 x 1. 0 inches (58. 7 x 62. 4 x 25 mm) 61 g (2. 15 ounces) 2. 4 x 2. 1 x 1. 0 inches (61. 4 x 53. 5 x 26 mm) 60 g (2. 12 ounces) PE823 PE826 PE828 PE829 1 x CR2032 3V 1 x CR2032 3V 1 x CR2032 3V 1 x 12V 2 x CR2032 3V PE826 SPECIFICATIONS TYPE Step counter Target step range Timer range Distance traveled Stride distance Calorie display Pulse range Operating temp. [. . . ]