User manual OREGON SCIENTIFIC BHGR618

[. . . ] Insert batteries in remote units before doing so for the main unit (see instructions for battery installation). Place the main unit as close as possible to the remote unit, reset the main unit after installing batteries. This will ensure easier synchronization between the transmission and reception of signals. [. . . ] If no signals are received, blanks " --- " will be displayed and the RF signal indicator will not show. To force a signal search: Press and hold IN/REMOTE for 2-seconds to enforce a 3-minute search. This is useful in synchronizing the transmission and reception of the remote and main units. Repeat this step whenever you find discrepancies between the reading shown on the main unit and that on the respective remote unit. If you press [MEM/CLEAR] now, the maximum and minimum reading will have the same values as the current ones until different readings are recorded. NOTE ON °C AND °F The unit of temperature display is selected on the °C/°F slide switch. Note that the remote temperature display on the main unit is dominated by the selection on the °C/°F slide switch of the main unit. Whatever the display units of the remote sensors are, they will be automatically converted to the chosen one of the main unit. COMFORT LEVEL INDICATORS The comfort level indicators COM, WET or DRY will tell you if the curent environment is comfortable, too wet or too dry. The comfort indicators will appear on the display of the main and remote units when the following conditions are satisfied: HOW TO CHECK REMOTE AND INDOOR TEMPERATURES & HUMIDITIES Display of readings from a remote sensor or the main unit is a one-step procedure. The remote sensor channel or the main unit display is indicated under the readings. To display indoor temperature & humidity : Press IN / REMOTE until "in" is displayed under the readings. To display remote temperature & humidity : Press CHANNEL until the appropriate remote sensor channel is displayed under the readings. If no readings are received from one particular channel for more than 15 minutes, blanks " --- " will be displayed until further readings are successfully searched. Check the remote sensor to ensure that it is secure and that the correct channel has been 3 Indicator displays on the unit Temperature Range Humidity Range Shows that the Current Environment Ideal range for both relative humidity and temperature Contains excess moisture. Contains inadequate moisture COM 20°C to 25°C (68°F to 77°F) -5°C -+ 50°C (23°F - 122°F) -5°C -+ 50°C (23°F - 122°F) Less than 20°C( 68°F) or More than 25°C (77°F) 40%RH70%RH OVER70%RH Below 70%RH 40%RH to 70%RH WET DRY No Indicator No comment GB GB HOW TO READ THE RF SIGNAL INDICATOR The RF signal indicator shows the signal-receiving status of the main unit. No signals. LOW BATTERY WARNING When it is time to replace batteries, the respective low-battery indicator will show up when the respective channel is selected. The battery level of the main unit will be shown on the indoor temperature when it is running low. THE RESET BUTTON To clear user-defined setting or if the unit is operating in an unfavorable way or malfunctioning use a blunt stylus to hold down the RESET button. All settings will return to the factory set defaults. REMOTE SENSOR SCANNING The unit can be set to automatically scan and display readings from the remote sensors. When the remote-sensor mode is active, the display will show the readings from one channel for about 4second and then proceed to the next channel display. To activate the remote-sensor scanning mode: Press and hold CHANNEL for 2-seconds. TABLE STANDING OR WALL MOUNTING Table-Standing : Your unit comes with stand connector for connecting it to other modular units. To deactivate the remote-sensor scanning mode: Press any button. STAND CONNECTOR DISCONNECTED SIGNALS If without obvious reasons the display for a particular channel goes blank, press[IN/REMOTE] to enforce an immediate search. [. . . ] Doing so will terminate the unit's warranty and may cause damage. Read this instruction manual thoroughly before operating the unit. Weight Main unit Remote sensing unit : 4. 47 ounces : 3. 17 ounces Dimensions Main unit(H xW xD) Remote sensing unit : 6. 54" x 2. 28" x 1. 26" : 6. 54" x 1. 57" x 1. 33" NOTE ON COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operations. [. . . ]