User manual OREGON SCIENTIFIC BAR688HGA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual OREGON SCIENTIFIC BAR688HGA. We hope that this OREGON SCIENTIFIC BAR688HGA user guide will be useful to you.
Manual abstract: user guide OREGON SCIENTIFIC BAR688HGA
Detailed instructions for use are in the User's Guide.
[. . . ] SENSOR DATA TRANSMISSION Data is sent from the sensor(s) every 40 seconds. ICON DESCRIPTION Main unit is searching for the sensor(s) A channel has been found Sensor 1 is sending data
1. Battery compartment
GETTING STARTED
SETTING UP THE CLOCK Insert batteries before first use, matching the polarity (+ and -). RESET after each battery change.
CLOCK OVERVIEW
FRONT VIEW
1. [. . . ] TEMP / HUMIDITY HI / LO : Change settings or enable / disable hi or lo temperature / humidity alarm for channel 1 2. / : Increase / decrease setting; activate / deactivate clock reception signal
For best results: · Place the sensor out of direct sunlight and moisture. · Do not place the sensor more than 30 m (100 ft) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission.
BAR688HGA_M
1
2005. 12. 2, 2:53 PM
ALARM
To set the alarm: 1. To silence the alarm: · Press SNOOZE to silence it for 8 minutes OR · Press any key except SNOOZE to turn the alarm off and activate it again after 24 hours.
To set alarm ON / OFF: 1. Press / to set alarm ON / OFF and press TEMP / HUMIDITY HI / LO to confirm. If alarm has been activated, use and to select the temperature / humidity. The alarm resets automatically and will resound if the hi / lo temperature selected is recorded again.
· Do not tamper with the unit's internal components. Doing so will invalidate the warranty on the unit and may cause unnecessary damage. · Only use fresh batteries as specified in the user's instructions. · Due to printing limitations, the displays shown in this manual may differ from the actual display. · The contents of this manual may not be reproduced without the permission of the manufacturer. NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.
device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] · To toggle between temperature / humidity and heat index display, press and hold HEAT INDEX for 2 seconds. NOTE If the heat index is below 80°F / 26°C, or the desired channel is not working, the heat index will display NA .
COMFORT ZONE
The comfort zone assesses the climate based on current temperature and humidity measurements. ICON TEMPERATURE Any 20 - 25°C (68 - 77°F) HUMIDITY > 70% 40 - 70% < 40%
Power REMOTE UNIT LxWxH Weight
Rainy
Transmission range 30 m (100 ft) unobstructed Temperature Range -30°C to 60°C (-22°F to 140°F) Power 2 x UM-4 (AAA) 1. 5 V batteries NOTE We recommend that you use alkaline batteries with this product for longer usage and lithium batteries in temperatures below freezing.
declare that the product Product No. : Product Name: BAR688HGA Wireless Weather Station with Temperature / Humidity Display and Self - Setting Atomic Clock Manufacturer: Address: IDT Technology Limited Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St. , Hung Hom, Kowloon, Hong Kong is in conformity with Part 15 of the FCC Rules. For international inquiries, please visit: www2. oregonscientific. com/about/international. asp
RESET
Press RESET to return the unit to the default settings.
PRECAUTIONS
This product is engineered to give you years of satisfactory service if you handle it carefully. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE OREGON SCIENTIFIC BAR688HGA
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual OREGON SCIENTIFIC BAR688HGA will begin.