User manual OREGON SCIENTIFIC BAR669

[. . . ] 9 Activate Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 BAR669 lab test R2 1 Silence Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Barometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Weather Forecast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The website also includes contact information for our customer service department, in case you need to reach us. 2 BAR669 lab test R2 2 1/17/04, 4:39 PM PRODUCT OVERVIEW FRONT VIEW 1. 9. SNOOZE / LIGHT button Weather Forecast & Barometric Trend Area Outdoor Temperature & Humidity Area Indoor Temperature & Humidity Area Clock / Alarm Area Moon Phase and : increase or decrease setting / activate or deactivate Atomic Clock. MEMORY: view current, maximum and minimum temperature / humidity readings 11. Altitude pressure: change measurement unit (mb/hPa or inHg) and value 3 BAR669 lab test R2 3 1/17/04, 4:39 PM EN EN BACK VIEW 1. 1 Wall mount Battery compartment Table stand REMOTE SENSOR (THGR122N) GETTING STARTED 2 3 4 BAR669 lab test R2 4 1/17/04, 4:39 PM REMOTE SENSOR (THGR122NX) 1 1 2 2 3 4 1. 4. Wall mount hole RESET Channel number (1 - 3) Battery compartment (Battery compartment cover not shown) 5 BAR669 lab test R2 5 1/17/04, 4:39 PM EN EN GETTING STARTED BATTERIES Batteries are not supplied with this product. You will need to purchase 3 x UM-3 (AA) 1. 5V alkaline batteries for the main unit, and 2 x UM-4 (AAA) 1. 5V alkaline batteries for the remote sensor. Insert batteries before first use, matching the polarity as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. UNIT Main Remote LOCATION Indoor Temperature / Humidity Area Outdoor Temperature / Humidity Area CHANGE SETTINGS 1. Press MODE to confirm. TABLE STAND OR WALL MOUNT Use the stand on the back of the product, or mount it on a wall with a nail. REMOTE SENSOR (THGR122NX) ACCESS FRONT BUTTON PANEL The front button panel is located inside the right portion of the main unit. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. To force a manual search for Atomic Clock signals, press and hold UP for 2 seconds. NOTE If the Atomic Clock signal is received and the hour is incorrect, use the "timezone offset" feature to adjust it to the appropriate timezone. 9 for instructions. 8 1/17/04, 4:39 PM BAR669 lab test R2 8 TURN ATOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Then, manually set the clock following the "Set Clock" instructions (below). No icon means that it is OFF SET CLOCK You only need to do this if you have disabled the Atomic Clock feature (for example, if you are too far from or cannot receive a signal). NOTE The language options are (E) English, (F) French, (D) German, (I) Italian, and (S) Spanish. NOTE The time zone options are (PA) Pacific, (CE) Central, (MO) Mountain, and (EA) Eastern. SWITCH CLOCK DISPLAY Press MODE to toggle between Clock with Seconds and Clock with Weekday display. ALARMS This product is equipped with a 2-minute crescendo alarm. Press ((. )) to confirm. ACTIVATE ALARM Press to activate or deactivate the Alarm. SILENCE ALARM When the Alarm time is reached, the crescendo alarm will sound for 2 minutes. [. . . ] NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]