User manual OREGON SCIENTIFIC BAR623PA

[. . . ] Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 11 11 12 12 13 13 13 13 13 14 14 14 14 15 16 16 16 16 16 16 17 17 18 19 EN EN INTRODUCTION Thank you for selecting the Oregon ScientificTM Atomic Projection Clock with Weather Forecast (BAR623PA). This device bundles precise time keeping with a projection clock, weather forecast, and indoor and outdoor temperature monitoring features into a single tool you can use from the convenience of your home. [. . . ] Extreme cold may temporarily reduce the effective range between the sensor and the base station. If the unit's performance fails due to low temperature, the unit will resume proper functioning as the temperature rises to within the normal temperature range (i. e. ICON DESCRIPTION Main unit is searching for the sensor A Channel has been found --- show in Outdoor Temp Area The sensor cannot be found. Search for the sensor or check batteries · · You may need to experiment with various locations to get the best results. Because of this they will freeze in low temperatures of approximately 10°F. Disposable Lithium batteries have a much lower threshold for temperature with an estimated freezing range of below -40°F. The Liquid Crystal Display in outdoor thermometers will 9 EN EN SEARCH FOR SENSOR To search for the sensor, press and hold SEARCH (on the main unit) for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. To force a manual search for atomic clock signals, press and hold for 2 seconds. If no signal is found, check the batteries. Once complete, the reception icon will stop blinking. STRONG SIGNAL WEAK SIGNAL NO SIGNAL TURN ATOMIC CLOCK SIGNAL ON / OFF CLOCK The clock automatically synchronizes the current time and date when it is brought within range of the WWVB60 atomic clock signal generated from Fort Collins, Colorado. boulder. nist. gov/timefreq/stations/radioclocks. htm NOTE The signals are collected by the main unit when it is within 932 miles (1500 km) of a signal. Initial reception takes 2-10 minutes, and is initiated when you first set up the unit, and whenever you press RESET. Then, manually set the clock following the "Set Clock" instructions. The signal icon indicates that the clock feature is ON. No icon means that it is OFF. SET TIME ZONE / CLOCK / CALENDAR You only need to do this if the unit is unable to synchronize with the atomic clock broadcast, or if you have disabled the atomic clock feature (see "Turn Atomic Clock Signal ON / OFF" section). Select the US time zone, hour, minute, year, month, day, and day-of-the-week language. NOTE The time zone options are (PA) Pacific, (CE) Central, (MO) Mountain and (EA) Eastern. NOTE The language options are (E) English, (F) French, (D) German, (I) Italian, and (S) Spanish. ALARM This product is equipped with a 2-minute crescendo alarm. VIEW ALARM SETTINGS Press . The alarm time and status will show in the Clock Area. SET ALARM 1. Press to confirm. ACTIVATE ALARM SWITCH CLOCK DISPLAY Press MODE to toggle between Clock with Seconds and Clock with Weekday display. shows in the Clock / Alarm Area when the alarm is activated. 11 EN EN SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off 18 and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio / TV technician for help. DECLARATION OF CONFORMITY The following information is not to be used as contact for support or sales. [. . . ]