User manual OREGON SCIENTIFIC BAR122HGA

[. . . ] Address: 19861 SW 95th Place, Tualatin, Oregon 97062, USA Telephone Number: 1-800-853-8883 Name and model number of the product: Remote Thermo-Hygro BAR122HGA : 7. 62 ounces (without battery) : 2. 6 ounces (without battery) : 5. 35" x 3. 54" x 1. 38" (LxWxD) : 4. 2" x 2. 8" x 0. 84" (L x Wx D) NOTE ON COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operations. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC : NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] If you wish to disable the auto-reception feature, press the ] button for three seconds. The radio reception signal [ TIME / [ ] and the outline of the US-Map icon will disappear. To enable the feature again, press the [ TIME / for three seconds. 10 1. The accuracy of a general pressure-based weather forecast is about 70% to 75%. The weather forecasts from this unit are predictions that cover the next 12 to 24 hours. The "Sunny" icon, implies clear weather. CALENDAR CLOCK DISPLAY MODES The BAR122HGA supports 2 time display modes in the sequence of: MODE 1. Hour-Minute-Second (of local time) Month-Day (of local time) ] (clock) button b122hga-e. p65 10 08/10/2001, 12:17 PM The high-low displays are as follows: Sequence Pressing HI/LO once Pressing HI/LO twice Pressing HI/LO third time Pressing HI/LO fourth time Respective Display Enters HI temperature display Enters HI humidity display Enters LO temperature display Enters LO humidity display display. The respective HI, LO or both indicators will be displayed to signify the status of the alarm. If a channel other than channel-1 is selected, the display will switch to channel-1 and flash when the alarm activates. Press either [CHANNEL], [MEMORY], [HI/LO], [ ], [ON/OFF] (TEMP % RH AL) to momentarily stop the alarm. The alarm will activate again if the limit continues to exceed the set limit. Note: If a second limit is passed while an alarm is active, the first alarm will complete its 1-minute cycle and the alarm will continue to activate for a second minute to indicate that a second limit has been surpassed. Display will show "---" to indicate such deactivation and will not sound at the previously set limit. To disable a sounding alarm: · Press either [CHANNEL], [MEMORY], [HI/LO], [ ], [ON/OFF] To set a high or low temperature or humidity alarm: 1. Press and hold the button for a rapid-scrolling sequence by increments of five. Note: The temperature range is from -50°C (-58°F) to +70°C (158°F). If this is the first time you set the limits, the lower limit will start from -50°C (-58°F) and the upper limit +70°C (158°F). If this is the first time you set the limits, the lower limit will start from 2% and the upper limit 98%. Repeat the steps to set the upper temperature and humidity setting and the lower temperature and humidity settings. When finished, press [HI/LO] to set another limit or wait 16 seconds and the unit will automatically return to the normal 9 b122hga-e. p65 9 (TEMP % RH AL) 08/10/2001, 12:17 PM GB GB TEMPERATURE, HUMIDITY & PRESSURE TREND INDICATORS The temperature-trend, humidity-trend and pressure-trend indicators show the trends of collected readings. Arrows indicate a rising, steady or falling trend. MAXIMUM AND MINIMUM TEMPERATURE AND HUMIDITY The maximum and minimum recorded temperature and humidity readings will automatically be stored in the memory. Press [MEMORY] once to display the maximum temperature and humidity and press [MEMORY] again to display minimum temperature and humidity. [. . . ] [ MEMORY ] BUTTON Displays minimum and maximum temperature and humidity readings and erases memory data E. [ MODE/SET ] BUTTON Changes the display mode of the clock and alters time/date setting G. US - TIME ZONE MAP ICON Displays Pacific (P), Mountain (M), Eastern (E) or Central (C) time-zone H. [ ((. )) ] ALARM ICON Appears when the alarm time is displayed ] BUTTON [ TIME / Decrease the value of a setting Q. [. . . ]