User manual OREGON SCIENTIFIC BAR112HGA

[. . . ] [ MODE/SET ] BUTTON Changes the display mode of the clock and alters time/date setting E. [ MEM ] BUTTON Displays minimum and maximum temperature and humidity readings and erases memory data G. [ 1 ] ALARM-ON ICON Appears when the alarm is activated US - TIME ZONE MAP ICON Displays Pacific (P), Mountain (M), Eastern (E) or Central (C) time-zone 2 Q. [ ZONE ] BUTTON Toggles between the 4 US time-zones : Pacific, Mountain, Eastern or Central R. [. . . ] When the remote-sensor scanning mode is active, the display will show the readings from one channel for about 4-second and then proceed to the next channel display. To activate the remote-sensor scanning mode: · Press and hold [CHANNEL] for 2 seconds. To deactivate the remote-sensor scanning mode: · Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) 7 WET DRY No Indicator No comment GB GB TEMPERATURE, HUMIDITY & PRESSURE TREND INDICATORS The temperature-trend, humidity-trend and pressure-trend indicators show the trends of collected readings. Arrows indicate a rising, steady or falling trend. MAXIMUM AND MINIMUM TEMPERATURE AND HUMIDITY The maximum and minimum recorded temperature and humidity readings will automatically be stored in the memory. Press [MEM] once to display the maximum temperature and humidity and press [MEM] again to display minimum temperature and humidity. To clear the memory: · Press and hold [MEM] for 2 seconds. Arrow indicator Temperature Trend Rising Steady Falling Arrow indicator Humidity Trend Rising Steady Falling If you press [MEM] now, the maximum and minimum recordings will have the same values as the current ones until different readings are recorded. Arrow indicator HOW TO USE CHANNEL-1 TEMPERATURE/ HUMIDITY ALARM Rising Steady Falling Pressure Trend Upper and lower temperature and humidity limits for Channel-1 can be set so that an alarm activates when the limits are exceeded. The high and low temperature and humidity displays are selected by sequentially pressing [ HI/LO ]. Note: If the reading goes above or below the measuring range of the main unit or the remote unit ( stated in specification), the display will show "HHH" or "LLL". 8 The high-low displays are as follows: Sequence Pressing HI/LO once Pressing HI/LO twice Pressing HI/LO third time Pressing HI/LO fourth time Respective Display Enters HI temperature display Enters HI humidity display Enters LO temperature display Enters LO humidity display display. The respective HI, LO or both indicators will be displayed to signify the status of the alarm. If a channel other than channel-1 is selected, the display will switch to channel-1 and flash when the alarm activates. Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) to momentarily stop the alarm. The alarm will activate again if the limit continues to exceed the set limit. Note: If a second limit is passed while an alarm is active, the first alarm will complete its 1-minute cycle and the alarm will continue to activate for a second minute to indicate that a second limit has been surpassed. Display will show "---" to indicate such deactivation and will not sound at the previously set limit. To disable a sounding alarm: · Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) To set a high or low temperature or humidity alarm: 1. The strength of the reception will remain until the next scanning cycle takes place. For better reception, place the clock away from metal objects and electrical appliances to minimize interference. If you wish to disable the auto-reception feature, press the [ ZONE ] button for three seconds. The radio reception signal [ ] and the outline of the US-Map icon will disappear. ] (clock) button for three To enable the feature again, press the [ seconds. The radio reception signal [ ] and the outline of the US-Map icon will start blinking to initiate reception automatically. 10 1. The accuracy of a general pressure-based weather forecast is about 70% to 75%. The weather forecasts from this unit are predictions that cover the next 12 to 24 hours. [. . . ] FCC : NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 13 GB GB CAUTION -- The content of this manual is subject to change without further notice. -- Due to printing limitation, the displays shown in this manual may differ from the actual display. [. . . ]