User manual OREGON SCIENTIFIC BAR1000A

[. . . ] [ RESET ] BUTTON Returns all settings to default values BATTERY COMPARTMENT Accommodates four (4) UM-3 or "AA" size batteries REMOVABLE TABLE STAND For standing the main unit on a flat surface FEATURES: REMOTE THERMO-HYGRO SENSOR A. TWO-LINE LCD Displays the current temperature and humidity monitored by the remote unit LED INDICATOR Flashes when the remote sensor transmits a reading °C/°F SLIDE SWITCH Selects between Centigrade (°C) and Fahrenheit (°F) CHANNEL SLIDE SWITCH Select the remote sensor Channel 1, Channel 2 or Channel 3 RESET Returns all user programmed settings to original factory set values BATTERY COMPARTMENT Accommodates two (2) UM-3 or AA-size batteries WALL-MOUNT HOLDER Supports the remote unit in wall-mounting REMOVABLE TABLE STAND For standing the remote unit on a flat surface B. Place the main unit as close as possible next to the remote unit, reset the main unit after installing batteries. This will ensure 3 GB GB easier synchronization between the transmission and reception of signals. Position the remote sensor and main unit within effective transmission range, which, in usual circumstances, range of 100 feet (30 meters) under ideal conditions. [. . . ] To force a signal search: · Press and hold [CHANNEL] & [MEM] for 2 seconds to enforce a 3-minute search. This is useful in synchronizing the transmission and reception of the remote and main units. Repeat this step whenever you find discrepancies between the reading shown on the main unit and that on the respective remote unit. To display temperature / humidity readings from a remote sensor: · Press [CHANNEL] until the appropriate remote sensor channel is displayed in the box under the kinetic-wave. DISCONNECTED SIGNALS If without obvious reasons the display for a particular channel goes blank, press [CHANNEL] & [MEM] to enforce an immediate search. Note that when the temperature falls below freezing point, the batteries of outdoor units will freeze, which will lower their voltage supply and the effective range. The transmission is within range and path is clear of obstacles and interference. Shorten the distance when necessary. HOW TO CHECK REMOTE AND INDOOR TEMPERATURE & HUMIDITY Display of readings from a remote sensor or the main unit is a onestep procedure. The remote sensor channel or the main unit display is indicated in a box under the kinetic-wave icon. Kinetic-wave Icon Designated Display Indoor Display Remote Remote Display Display Channel 1 Channel 2 Remote Display Channel 3 TRANSMISSION COLLISION Signals from other household devices, such as door bells, home security systems and entry controls, may interfere with those of this product and cause temporary reception failure. This is normal and does not affect the general performance of the product. The transmission and reception of temperature and humidity readings will resume once the interference recedes. To display temperature / humidity readings from the main unit: · Press [CHANNEL] until a dot is displayed in the box under the kinetic-wave. 6 HOW TO READ THE KINETIC WAVE DISPLAY The kinetic wave display shows the signal receiving status of the main unit. No signal received in search mode. COMFORT LEVEL INDICATORS The comfort level indicators COM, WET or DRY will tell you if the curent environment is comfortable, too wet or too dry. The comfort indicator will appear on the display when the following conditions are satisfied: Indicator displays on the unit Temperature Range Humidity Range Shows that the Current Environment Ideal range for both relative humidity and temperature Contains excess moisture. The effective range covers an area of 18 to 30 miles. Indicator displays on the unit MODE 2. Hour-Minute-Day of the Week (of local time) Month-Day (of local time) Each press on the [MODE/SET] button will toggle the display in the above order. Note: The bottom line of the display will be replaced by the alarm ] button is pressed. time if the [ Forecast NOTE: Sunny Slightly Cloudy Cloudy Rainy ABOUT RADIO RECEPTION The BAR112HGA is designed to automatically synchronize its calendar clock when it is within range of the radio signal from the U. S. When the unit is receiving radio signal, the RADIO RECEPTION signal will start to blink. A complete reception generally takes about 2 to 10 minutes, depending on the strength of the radio signal. Without interruption, the alarm will sound for a total of two minutes. If no key is pressed to turn off the alarm within these 2 minutes, the alarm will sound once more after 8 minutes. - Receiving HOW TO SET THE CLOCK MANUALLY To set the clock manually, hold [MODE/SET] for three seconds. Repeat the same procedure to set the minutes, year, month, day and display language. For the language display, you can choose among English (E), French (F) and Spanish (s). 11 GB GB HOW TO STOP AN ALARM To stop an alarm, you can use either press [ ] button or [ AL ON/OFF ] button. Pressing [ ] will stop the alarm, which is still armed and will activate at the set time the following day. [. . . ] o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Address: 19861 SW 95th Place, Tualatin, Oregon 97062, USA Telephone Number: (1)503-6398883 Name and model number of the product: Digital Weather Forecaster with Remote Thermo-Hygro sensor and Radio Controlled Clock BAR112HGA : 6. 6 ounces (without battery) : 2. 6 ounces (without battery) : 6. 44" x 3. 48" x 1. 12" (LxWxD) : 4. 2" x 2. 8" x 0. 84" (L x Wx D) NOTE ON COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operations. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]