User manual OPTICON PHL 2700

[. . . ] Laser Terminal PHL 2700 Cradle IRU 2700 User's Manual USER'S MANUAL PHL2700 TERMINAL / IRU2700 CRADLE CAUTION: This user's manual may be revised or withdrawn at any time without prior notice. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon Sensors Europe. Limited warranty and disclaimers By opening the package of this product you agree to become bound by the liability and warranty conditions as described below. Under all circumstances this manual should be read attentively, before installing and or using the product. [. . . ] If the terminal with penlite batteries is placed in the cradle, the cradle will not show an indication. 2. 5. 3 When to replace or recharge the main battery?All batteries have to be used together with Opticon battery case for dry cell batteries. Batteries that are not supplied by Opticon must be AA-size and absolutely leakproof. If rechargeable batteries are used, they need to be recharged by a separate battery charging device. Opticon recommends to use Opticon batteries (Opticon rechargeable battery pack or Opticon dry cell batteries) only. Backup Battery Use only one type of battery for backup: Backup battery: CR2032 Li (Lithium, button type). There are 2 reasons for replacing the main battery; as soon as possible after the battery indicator appears on the display. For instructions of (re)placing the main battery see paragraph 2. 5. 5. 2. 5. 4 When to replace the backup battery?For instructions of (re)placing the backup battery see paragraph 2. 5. 6. 11 USER'S MANUAL PHL2700 TERMINAL / IRU2700 CRADLE 2. 5. 5 How to (re)place the main battery in the terminal? ! 1 ----> open Only use batteries as specified in paragraph 2. 5. 1. If you have data stored, make sure the backup battery is placed and full enough, to avoid data loss. ! Before installing a battery case with penlite batteries: Make sure you use the right battery size. Place 2 batteries in the battery holder aligning plus (+) and minus (-) ends as shown on the battery holder. close <---- The instructions for installing the rechargeable battery pack are also applicable for the battery case with penlite batteries. Unlock cover: Open the switch (shift to the right) and remove the battery case cover (ref. 1) Remove main battery pack: Hold your tumb over the right wing of the battery case. Check if the charging contacts of the case align with the contacts inside the battery compartment (ref. 3) Fit main battery pack: First place the left side of the battery case into position (ref. Click the left wing untill it fits followed by clicking the right wing. 4b) Fit cover: Place the battery case cover and lock the switch (shift to the left) (ref. 1) 2a 2b 3 3 4a 4b 12 USER'S 2. 5. 6 How to (re) place the backup battery in the terminal? ! MANUAL PHL2700 TERMINAL / IRU2700 CRADLE Make sure that the main battery is full enough while changing the backup battery. Unlock cover: Open the switch (shift to the right) and remove the battery case cover (ref. 1) Open lid: Place your thumbnail below the saving of the lid to open it (ref. 5) Remove backup battery: Take the old battery out of the compartment. Place backup battery: Make sure that the positive side of the backup battery is pointed upwards and place it in the compartment (ref. [. . . ] When the terminal needs to be repaired, please ensure that the label with the serial number is still present. If sending the terminal or cradle, please use the original packing to minimise the chances of damage. The terminal looses data when the battery pack is removed for a short period. ? The backup battery is empty. Replace the Lithium CR2032 battery by a new one. 20 USER'S MANUAL PHL2700 TERMINAL / IRU2700 CRADLE 7. 2 READ OPERATION PROBLEMS When the terminal has a problem with reading the label: ? 7. 3 BATTERY CHARGING PROBLEMS When the terminal is placed in the cradle, the main battery is not charged. ? The resolution of the bar code is too high. Decrease the distance between the bar code and the terminal. Red LED indicator on the terminal is flashing on and off. [. . . ]