User manual OPTICON PHL 1300

[. . . ] User's Manual Pocket Terminal PHL1300 Cradle IRU1300 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE CAUTION: This user's manual may be revised or withdrawn at any time without prior notice. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon Sensors Europe. Limited warranty and disclaimers By opening the package of this product you agree to become bound by the liability and warranty conditions as described below. Under all circumstances this manual should be read attentively, before installing and or using the product. [. . . ] No other types of terminals can be placed into this cradle. 1 2 3 4 Start with a full battery To be sure of proper operation, it is advised to start with a full battery, charge the battery pack according to the instructions in the next chapter. Click the battery pack into the terminal, as instructed in the next chapter. 10 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 5 INSTALLING, REPLACING AND CHARGING BATTERIES Wrong use of batteries might cause serious damage to the terminal or to the cradle. In order to avoid damage it is very important to take notice of the instructions. ! Insert full batteries before use of the terminal. When you do not use the terminal for a long time, make sure the main battery has enough capacity. Place 2 batteries in the battery holder aligning plus (+) and minus (-) ends as shown inside the battery compartment. Lock main battery case cover: Position the case cover and fix its position by screwing hand tight. 2. 5. 2 How to charge the rechargeable battery pack in the cradle? Make sure that the Opticon rechargeable battery pack is inserted in the terminal. If the terminal with the battery pack is placed in the cradle, the LED on the cradle will turn green. When the terminal is placed in the cradle, the rechargeable battery pack will be charged automatically for 8 hours. 2. 5. 3 When to replace or recharge the main battery? There are 2 reasons for replacing the main battery; as soon as possible after the battery indicator appears on the display. when you are not using the terminal for an extended period. 2. 5. 4 When to replace the backup battery? When low battery mark appears, replace the battery without delay. 12 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 5. 6 How to (re) place the backup battery in the terminal? ! Make sure that the main battery is full enough while changing the backup battery. Only use CR2032 Li (Lithium, button type) battery. ! Unlock backup battery case cover: (ref. a) Unlock the case cover by use of a small crosshead screwdriver or swatch screwdriver. b) Make sure that the positive side of the battery is pointed upwards (visible) and place it in the compartment. Lock backup battery case cover: Position the case cover and fix its position by screwing hand tight. 1 2 3 a b 13 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 6 INSTALLING IN A SYSTEM ! Exercise caution at all times when working with AC-powered equipment. Because of the special pin-out of the connectors, use the cables supplied by the manufacturer. When you need another cable for a certain device, that is not supplied, contact your supplier to purchase the right cable. In case another cable is used, take notice of the pin-out specifications further in this manual. ! ! ! Connection sequence for single cradle: Place the cradle in normal office conditions, avoid a place under strong light. Place the PHL1300 terminal in the cradle. 2. 6. 1 Single cradle DB25 / DB9 HOST DB9 CRADLE RS 232 Connection sequence for cradle network: Set all cradles to the same baud rate (by DIPswitch) Only 1 cradle in the network will be connected to the PC through one RS232 cable. A maximum of 16 cradles can be connected in a network through RS485 cables. For the cradles that are not directly connected to the PC the DIPswitch for RS232 connection must be set to off. The first and the last cradle in the network must have the termination resistors set by dipswitch. 2. 6. 2 Cradle network TRANSMISSION HOST RS 232 TERMINATED RS 485 sw 1 = on sw 2 = on sw 3 = on RS 485 sw 1 = off sw 2 = off sw 3 = off // RS 485 TERMINATED sw 1 = off sw 2 = on sw 3 = on 14 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 6. 3 DIP switch settings on cradle Setting the DIP switches on or off will result in differrent baudrates and enabled or disabled functions of the cradle. Open the cover of the DIP switches on the bottom of the cradle in order to reach the DIP switches. Turn the DIP switch ON by moving it upwards into the direction of the dipswitch number. [. . . ] 170 g (depending on battery type) Immunity 6. 2. 4 Physical specifications Dimensions Case material Standard connector (l x w x h) 134 x 78 x 75 mm ABS RS232 - D Sub 9P Female RS485 - 6 pins modular plug 19 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 3 7 TROUBLE SHOOTING This chapter contains information on solving problems you may encounter when using the terminal and/or cradle. If problems occur, first carry out some general checks, before verifying the problem with the descriptions in this chapter. General checks: Make sure everything is installed properly Check the power supply of all devices Is the reading window of the terminal clean?not damaged or poorly printed? If the equipment still does not work after these checks have been performed, please verify if one of the problems described in this chapter applies to the problem you have with the scanner. It is possible that you may not solve the problems, despite our descriptions. [. . . ]