User manual OPTICON OPV 1001

[. . . ] Laser Multi-barcode Scanner OPV 1001 The OPV 1001 is a 1000 scans multi-barcode laser scanner reading for omni-directional reading. Specifications Manual Opticon OPV 1001 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPV 1001 6 2008-04-07 Specification Number: Original Spec Number: SS06175 SS06172 Copyright 2008 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. This official registration number is directly related to the device purchased. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. [. . . ] You can use a dedicated stand (an accessory, sold separately) to adjust the height and angle of the scanner. The feature settings of the OPV 1001 are configured either by scanning menu barcodes or by sending commands. The OPV 1001 outputs scanned data through any of the following interfaces: RS-232C, Keyboard Wedge, or USB. add-on Codabar/NW-7 Code 11 Code 39 Code 93 Code 128 GS1-128 (EAN-128) IATA Industrial 2of5 Interleaved 2of5 ISBN-ISMN-ISSN Matrix 2of5 MSI/Plessey S-Code Telepen Tri-Optic UK/Plessey Postal Code Chinese Post 7 Opticon OPV 1001 Specifications Manual 3. Weight OPV 1001: 200 g (max. ) excluding the cable Stand: 340 g (max. ) 4. Operating Temperature and Humidity Temperature: 0 to +40° C Humidity: 20 to 90% RH 4. 2. Storage Temperature and Humidity Temperature: -30 to +60° C Humidity: 20 to 90% RH 4. 3. Ambient Light Immunity Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values: Incandescent light Fluorescent light Sunlight 3, 000 lx 3, 000 lx 20, 000 lx Conditions Barcode Sample: OPTOELECTRONICS Test Sample PCS: Resolution: Symbology: Quiet zone: N/W ratio: Distance: Angle (see note below): Curvature: Power supply voltage: 0. 9 0. 25 mm 9-digit Code 39 10 mm 1:2. 5 150 mm = 0° = 15° = 0° R= 5. 0 V Direct light or specular reflection from a light source should be prevented from entering the acceptance area. Please see section 0 for how these values are defined. 8 Opticon OPV 1001 Specifications Manual 5. Power Supply Input voltage Power ripple Current consumption DC 5 V ±5 % (6 V also supported) up to 100 mVp-p (10 Hz to 100 kHz DC 5V) up to 500 mA Conditions: · · · Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. The current value depends on the interface type and the host computer to which the device is connected. 5. 2. AC Adapter Input: Input voltage Power supply frequency Maximum current Rush current Output: Output voltage Output ripple Maximum current Startup time DC 5 V ±5% (6 V also supported) up to 100 mVp-p 2000 mA up to 20 ms (AC100V/50 Hz, 5% to 95% of output voltage) AC 90 V to 264 V 47 Hz to 63 Hz up to 400 mA (at 100 V AC/50 Hz) up to 70 A 5. 3. Red · · Lights up when any unsupported menu is read in the menu mode (200 ms with error buzzer). Green · Good read: when reading is done successfully. 9 Opticon OPV 1001 Specifications Manual 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Specification Red laser diode 650 ±10 (25° C) 1. 0 or less (measured at the front of the scanner's plastic mask) Rastering omni-directional scanning 1000 ±50 Unit ­ nm mW ­ scans/s 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 1000 lx Barcode = black Space = white Margin = white Background of label = black 5. 0 V Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 7. 1. Print Contrast Signal (PCS) 0. 45 or higher (over 70% of reflectivity of space and quiet zone). PCS= Reflectance of white barReflectance of black bar Reflectance of white bar Scanning performance may decline if dirt or scratches mar the optical window. Minimum Resolution 0. 127 mm 10 Opticon OPV 1001 Specifications Manual 7. 3. Scan Area The scannable area depends on the barcode type (PCS, resolution, length, etc. ) and the direction of the barcode surface. [. . . ] Power Saving The motor options are only applicable for selected laser bar code readers and with trigger enabled. To reduce the start-up time of the motor, the motor can be configured to half speed in idle mode. The Auto shutoff time can be configured between 1 and 9999 seconds, by reading 1 up to 4 direct input numeric characters from chapter: String options. A value of 0 (default) means that the barcode reader enters the idle state if the read time has expired. 17. 1. [. . . ]