User manual OPTICON OPR 3001

[. . . ] Rugged Handheld Laser Scanner OPR 3001 The OPR 3001 is a rugged handheld laser barcode scanner with protection against dust and splashing water to ensure reliable operation in harsh environments Specifications Manual Opticon OPR 3001 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPR 3001 2A 2006-12-27 Specification Number: Original Spec Number: SS06106 SS06080 Copyright 2006 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. This official registration number is directly related to the device purchased. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. [. . . ] The OPR 3001 is enclosed in a rugged housing sealed to IP-54 standards that withstands repeated drops of up to two meters onto concrete. Short-wavelength red laser beams enhance the visibility of scanning lines for easier aiming under adverse lighting conditions. add-on Codabar/NW-7 Code 11 Code 39 Code 93 Code 128 GS1-128 (EAN-128) GS1 Databar (RSS) IATA Industrial 2of5 Interleaved 2of5 ISBN-ISMN-ISSN Matrix 2of5 MSI/Plessey S-Code Telepen Tri-Optic UK/Plessey Postal Chinese Post Korean Postal Authority Code 2D Composite codes MicroPDF417 PDF417 7 Opticon OPR 3001 Specifications Manual 3. Dimensions W 68 X D 150 X H 155 mm (except protruding portion) 3. 2. Operating Temperature and Humidity Temperature: -10 to +60° C Humidity: 5 to 90% RH 4. 2. Storage Temperature and Humidity Temperature: -30 to +70° C Humidity: 5 to 90% RH 4. 3. Ambient Light Immunity Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values: Incandescent light Fluorescent light Sunlight to 4, 000 lx to 4, 000 lx to 80, 000 lx Figure 1: Ambient light immunity 8 Opticon OPR 3001 Specifications Manual Conditions Barcode Sample: OPTOELECTRONICS Test Sample PCS: Resolution: Symbology: Quiet Zone: N/W Ratio: Distance: Angle: Curvature: Power supply voltage: 0. 9 0. 25 mm 9-digit Code-39 10 mm 1:2. 5 100 mm from the edge of scanner = 0° = 15° = 0° R= 6. 0 V Direct light or specular reflection light from a source should be prevented from entering the acceptance area. Electrical Characteristics Parameter Power supply voltage Symbol Min 5. 4 4. 5 -- Typ 6. 0 5. 0 96 90 400 300 35 30 Max 6. 6 5. 5 130 125 600 500 60 55 Unit V V mA mA mA mA mA mA RS-232C Remarks USB and Wedge RS-232C when emitting USB and Wedge when emitting laser RS-232C USB and Wedge RS-232C USB and Wedge Operating current IOP -- -- Rush current IPEEK -- -- Stand-by current IPRE -- Conditions: · · · Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. The current value depends on the host computer to which the device is connected. 9 Opticon OPR 3001 Specifications Manual 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Scan angle Specification Red laser diode 650 ±10 (25° C) 1. 0 or less Bi-directional scanning 100 ±20 Scan angle: 54 ±5 Read angle: 44 (Min) Unit -- nm mW -- scans/s ° ° mm Auto-trigger IR detection area 40 Notes: Refer to chapter 15, "Trigger and Read Options, " to read about the scan modes. Refer to chapter 7, "Technical Specifications, " to read about scanning performance. Tilt of Laser Scan Line Laser scanning tilt is the vertical difference between both ends of a laser scan line. Maximum tilt between both ends of laser scan line: Less than 1. 2° upward tilt from the scan origin. Maximum of 3. 1 mm when measured at a point 150 mm away from the scan origin. (The skew angle of this measurement was zero degrees. ) 10 Opticon OPR 3001 Specifications Manual 6. 1. 2. Curvature of Scan Maximum gap between the straight line connecting both ends of the laser scan line and the actual laser scan line: Less than 1. 27° curvature from the scan origin. Maximum of 3. 3 mm curvature when measured at a point 150 mm away from the scan origin. (The skew angle of this measurement was zero degrees. ) · Measurement was done from the center of the scan origin. Figure 2: Laser scanning tilt and curvature 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Angles: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Omni-scanning mode: Pitch: = 0°, Skew: = 0­10°, Tilt: = 0° Mobile mode: Pitch: = 0°, Skew: = 0°, Tilt: = 0° Barcode = black Space = white Margin = white Background of label = black 6. 0 V (RS-232C) / 5. 0 V (USB and Wedge) Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 11 Opticon OPR 3001 Specifications Manual 7. 1. Print Contrast Signal (PCS) 0. 45 or higher (over 70% of reflectivity of space and quiet zone). [. . . ] The reader will stay on for a time as set in 'Read time options'. The trigger signal can be initiated in the following ways: Auto trigger mode: The read cycle automatically starts when a trigger signal is received via sensor detection. 15. 2. Auto Trigger Sensor Auto trigger mode is enabled by scanning a part of scan area with infrared. The scanner will start scanning after the embedded CMOS sensor detects a change in reflection from the object. [. . . ]