User manual OPTICON OPR 2001

[. . . ] Laser Barcode Scanner OPR 2001 The OPR 2001 is a handheld laser barcode scanner. Specifications Manual Opticon OPR 2001 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPR 2001 1A 2007-02-14 Specification Number: Original Spec Number: SS07011 SS06121 Copyright 2007 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. This official registration number is directly related to the device purchased. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. [. . . ] Please see section 7 for how these values are defined. 9 Opticon OPR 2001 Specifications Manual 5. Electrical Characteristics: RS-232C Parameter Power supply voltage Operating current Peak current Standby current Startup time Symbol VDD IOP IPEAK IPRE TD Min 4. 5 -- -- -- -- Typ 6. 0 90 550 35 100 Max 6. 5 150 600 70 -- Unit V mA mA mA ms Notes No buzzer 5. 2. Electrical Characteristics: USB, Wedge Parameter Power supply voltage Operating current Peak current Standby current Startup time Symbol VDD IOP IPEAK IPRE TD Min 4. 5 -- -- -- -- Typ 5. 0 90 450 35 100 Max 5. 5 150 500 70 -- Unit V mA mA mA ms Notes No buzzer Conditions · · · Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. The current value depends on the interface type and host computer to which the device is connected. 10 Opticon OPR 2001 Specifications Manual 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Scan angle Specification Red laser diode 650 ±10 (25° C) 1. 0 or less Bi-directional scanning 100 ±20 Scan angle: 54 ±5 Read angle: 44 (Min) Unit -- nm mW -- scans/s ° ° Notes: Refer to chapter 15, "Trigger and Read Options, " to read about the scan modes. Refer to chapter 7, "Technical Specifications, " to read about scanning performance. Tilt of Laser Scan Line Scanning tilt is the vertical difference between the ends of a laser scan line. · Up to 0. 92° in a vertical direction from the scan origin (mirror motor mirror). Curvature of Scan Scanning curvature is the maximum difference between the laser scan line and the line between the ends of the laser scan line. · Up to 1. 17° in a vertical direction from the scan origin (mirror motor mirror). · Up to 3. 06 mm when measured at 150 mm from the scan origin. 11 Opticon OPR 2001 Specifications Manual Measurement is done from the center of the laser scan line. Figure 2: Laser scanning tilt and curvature 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Barcode = black Space = white Margin = white Background of label = black 6. 0 V (RS-232C) / 5. 0 V (USB, Wedge) Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 7. 1. Print Contrast Signal (PCS) 0. 45 or higher (over 70% of reflectivity of space and quiet zone). PCS= Reflectance of white barReflectance of black bar Reflectance of white bar Scanning performance may decline if dirt or scratches mar the optical window. Minimum Resolution 0. 127 mm 12 Opticon OPR 2001 Specifications Manual 7. 3. Depth of Field The depth of field is measured from the edge of the scanner. The scanning range is within the circular arc centered on the scan origin. Figure 3: Depth of field Symbology Code 39 Code 39 Code 39 Code 39 Code 39 Resolution 1. 0 mm 0. 5 mm 0. 25 mm 0. 15 mm 0. 127 mm Decode Depth (mm) 40­500 20­350 20­200 20­100 30­70 PCS 0. 9 0. 9 0. 9 0. 9 0. 9 Conditions Barcode Sample: OPTOELECTRONICS Test Sample N/W Ratio: Angle: Curvature: 1:2. 5 = 0°, = 15°, = 0° R= 13 Opticon OPR 2001 Specifications Manual Resolution 1. 0 mm 0. 5 mm 0. 25 mm 0. 15 mm 0. 127 mm Symbology Code 39 Code 39 Code 39 Code 39 Code 39 PCS 0. 9 0. 9 0. 9 0. 9 0. 9 Quiet Zone 25 mm 18 mm 10 mm 7 mm 5 mm Digits 1 3 8 10 4 7. 4. Pitch Angle Scanning performance is guaranteed when = ±35° Figure 4: Pitch 14 Opticon OPR 2001 Specifications Manual 7. 4. 2. Skew Angle and Dead Zone Scanning performance is guaranteed when skew angle: ±50° (Excluding dead zone) Dead zone: = ±8° (There are some areas in which decoding fails due to specular reflection) Figure 5: Skew angle and dead zone 15 Opticon OPR 2001 Specifications Manual 7. 4. 3. Tilt Angle Scanning performance is guaranteed when ±20° Figure 6: Tilt angle Conditions Barcode Sample: OPTOELECTRONICS Test Sample Distance: Label: 70 mm from the front edge of the scanner Pitch, Skew Angle, Dead Zone PCS = 0. 9, Resolution = 0. 25 mm, Symbology = 9-digit Code 39, Quiet Zone = 10 mm, N/W Ratio = 1:2. 5 Tilt Angle PCS = 0. 9, Resolution = 0. 26 mm, Symbology = 13-digit JAN, Quiet Zone = 10 mm Pitch angle: Skew angle: = +15°, Tilt angle: = 0° Tilt angle: Pitch angle: = 0°, Skew angle: = +15° Skew angle, Dead zone: Pitch angle: = 0°, Tilt angle: = 0° R= Angles: Curvature: 16 Opticon OPR 2001 Specifications Manual 7. 5. [. . . ] Barcode sheet: OPTOELECTRONICS Test Sheet (black) Background: OPTOELECTRONICS Test Sheet (white) Figure 27: Auto trigger operation Auto trigger can be enabled in 2 ways: · Stand detection mode: This option enables auto trigger automatically in case the scanner is inserted into the stand. *Descriptions in ( ) show menu IDs. 38 Opticon OPR 2001 Specifications Manual Figure 28: Trigger options 39 Opticon OPR 2001 Specifications Manual 16. Enable/Disable Settings Use the following settings to enable or disable the auto trigger. To enable auto trigger, scan "ZZ", "+I" and "ZZ" in that order. [. . . ]