User manual OPTICON OPL 2724

[. . . ] Wireless Barcode Scanner OPL 2724 The OPL 2724 scanner uses wireless Bluetooth 1. 2 technology. Scanned data is transferred to the designated device via wireless communication. Specifications Manual Opticon OPL 2724 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPL 2724 1A 2006-09-15 Specification Number: Original Spec Number: SS07003 SS05066 Copyright 2006 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. This official registration number is directly related to the device purchased. [. . . ] 15 Figure 6: Tilt angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 7: Curvature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 8: Serial number diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 9: Mechanical drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Abstract This document provides master specifications on the OPL 2724 wireless barcode scanner (hereafter referred to as "scanner"). 2. Scanned data is transferred to the designated device via wireless communication (Bluetooth V1. 2). Please see section 8 for how these values are defined. 8 Opticon OPL 2724 Specifications Manual 5. Controls Item CPU Clock frequency SRAM: Flash ROM: Specifications 16-bit CISC CPU 14. 74 MHz 32 KB 256 KB Notes For WORK/DATA For BIOS/AP 6. Absolute Maximum Ratings Parameter Power supply voltage Symbol VCC Value -0. 3 to 3. 6 Unit V 6. 2. Electrical Characteristics: Current Consumption Item In standby state In communication Maximum current Testing conditions Specifications 1. 5 mA or less 35 mA or less 125 mA or less Conditions No Bluetooth communication; no laser scanning With Bluetooth communication; no laser scanning With Bluetooth communication; with laser scanning Power supply voltage: 3. 0 V, Operating temperature: 25° C 6. 3. Main Battery The main battery power is provided by LR-03 (two AAA alkaline batteries). 6. 4. Battery Operating Time and Charging Time Parameter Battery life (1) Battery life (2) Specification About 48 hours Note Scanning twice every 10 seconds; Bluetooth always ON. When scanning 100 times a day. (Connect Bluetooth only when transmitting data. ) 30 days or longer 48 hours; Lithium secondary battery (3. 4 mAh) 1. 5 mA or less Data retention time Current consumption Operating conditions After the discharge of main batteries. In stand-by state 125 mA or less Normal temperature Barcode sample: Code-39 (PCS: 0. 9, Resolution: 0. 25 mm) In operating state Note: Battery life may be shorter than specified above when the quality of the battery pack is degraded. 9 Opticon OPL 2724 Specifications Manual 6. 5. Operating Indicators The OPL 2724 displays its operating state with LEDs and a buzzer. Action Start-up beep Indicator / Buzzer 6 short beeps (low, medium, high, low, medium, high) Blue LED is flashing Blue LED is flashing slow Description Battery is placed in OPL 2724 (start-up buzzer) OPL 2724 is attempting to establish a Bluetooth connection OPL 2724 is connectable (as slave) Bluetooth connection was (re)established The user has pressed the trigger long enough to create or break the connection. Connection attempt failed Connection loss is detected During `Auto reconnect time' every 15 or 30 seconds (depending on connection type) OPL 2724 is disconnecting a Bluetooth connection OPL 2724 successfully disconnected the Bluetooth connection Valid barcode label read with an active Bluetooth connection Valid barcode label read and stored in memory (data is not transmitted; i. e. , because there is no active Bluetooth connection Valid barcode label read with no active Bluetooth connection Partial read beep of (Micro)PDF417 decoder Valid Bluetooth action label read (i. e. , connect / disconnect / unpair ) Bluetooth action label read that could not be executed because OPL 2724 was already (dis)connected Menu book configuration mode Low battery indicator Error correction busy of (Micro)PDF417 data with a high error correction level Buzzer loudness was estimated at a point 10 cm behind the scanner. Connecting / Connectable Blue LED on and high sound for 1 second When pressing trigger: High-low sound of 0. 2 seconds followed by the blue or red LED flashing. Red LED on with low sound for 1 second Disconnecting / Connection failure Connection lost Red LED is flashing Red LED on and a long high-low sound for 1. 6 seconds Green LED and beep as configured in the Universal Menu Book at Chapter 6. 1. and 6. 2 Short green LED and beep of half the length as configured in the Universal Menu Book at Chapter 6. 1 and 6. 2 Orange LED as configured in the Universal Menu Book at Chapter 6. 2 with low sound Short click sound High-low sound with LED: Green (Misc. ) / Red (Disconnect) / Blue (Connect) Orange LED on and low sound of 0. 2 seconds Slow beeping sound Very slow blinking red LED Barcode reading Action / configuration label reading Miscellaneous Buzzer Green LED flashes and 8 high short beeps Loudness: 70 dBA or higher (when the scanner is set to "Loud") 10 Opticon OPL 2724 Specifications Manual 7. Optical Specifications Parameter Light source Wavelength Light output Scanning method Scanning rate Scanning angle Effective scanning angle Resolution Specification Red laser diode 650 ± 10 (at 25° C) JIS C 6802 Class 1 1. 0 (JIS Class 2) Bi-directional 100 ± 20 54 ± 5 44 (Min) 0. 127 or higher Unit -- nm mW -- scans/s ° ° mm Notes: Refer to chapter 8, "Technical Specifications, " to read about scanning performance. Tilt of Laser Scan Line Maximum tilt between both ends of laser scan line: Less than 1. 2° upward tilt from the scan origin. Maximum of 3. 1 mm when measured at a point 150 mm away from the scan origin. (The skew angle of this measurement was zero degrees. ) Measurement was done from the center of scan line. Curvature of Scan Maximum gap between the straight line connecting both ends of the laser scan line and the actual laser scan line: Less than 1. 27° curvature from the scan origin. [. . . ] The estimate of MTBF and product life cycle is based on standard operation of the product within the recommended temperature range and without extreme electronic or mechanical shock. JIS C6802: 2005: Laser class 1 IEC 825-1/EN 60825-1: Laser class 1 FDA CDRH Laser class I. Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to laser notice No. Class I1 laser devices are not considered to be hazardous when used for their intended purpose. [. . . ]