User manual OPTICOM VDC22X DATASHEET

[. . . ] This symbol indicates important instructions accompanying the product. WARNING :  To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION :  TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • This apparatus shall always be connected to a AC outlet with a protective grounding connection. • To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. [. . . ] Wait until the indicator blinks in white twice more, and then release the WPS/RESET button. • The indicator blinks in red, and then stops blinking and glows in red when the unit accesses the Network Setting mode. 3. To connect the Wireless Audio with Dock to the network, search for "Samsung W_Audio E670 XXXXXXX" in the Wi-Fi Setting list of your WI-Fi device, and then select it. ex) Samsung Galaxy Device or 4. Open the web browser of the Wi-Fi device, and then type "http://192. 168. 1. 1" into the address bar of the Internet browser to access the Wireless Audio with Dock's web page. 5. In the "Service Set ID (SSID)" field, select the AP device (router or modem) your Wi-Fi device is connected to. 6. Type the AP device's password into the "WPA Passphrase" filed. 8. When the connection between the Wireless Audio with Dock and AP you selected is completed, the indicator on the Wireless Audio with Dock changes to white. • The Wireless Audio with Dock connection is complete. 7 6 5 6  The picture above is the screen which will appear on the display after completing the network connection successfully, so you can run AirPlay or DLNA normally. 18 To connect the Wireless Audio with Dock using a WPS PIN 1. Press the button on the top panel of the Wireless Audio with Dock repeatedly until the icon appears in the display. • Each time you press the button, the selection changes as follows : ; ; ; ; ; ; AUX (LED Off) The indicator changes from white to red and blinks. 2. Press and hold the WPS/RESET button on the back panel with a pen tip or similar item for more than 5 seconds. Wait until the indicator blinks in white twice more, and then release the WPS/RESET button. ▪▪ Connect only to a Bluetooth device that supports the A2DP (AV) function. ▪▪ You cannot connect to a Bluetooth device that supports only the HF (Hands Free) function. ▪▪ Once you have turned off the Wireless Audio with Dock and the pairing is disconnected, the pairing will not be restored automatically. To reconnect, you must pair the devices again. ▪▪ The Wireless Audio with Dock may not search or connect properly in the following cases: -- If there is a strong electrical field around the Wireless Audio with Dock. -- If several Bluetooth devices are simultaneously paired to the Wireless Audio with Dock. -- If the Bluetooth device is turned off, not in place, or malfunctions -- Note that such devices as microwave ovens, wireless LAN adaptors, fluorescent lights, and gas stoves use the same frequency range as the Bluetooth device, which can cause electric interference. 20 CONNECTING TO BLUETOOTH DEVICES This section explains how to connect the Wireless Audio with Dock to Bluetooth compatible TVs and other Bluetooth devices. EnG To connect the Wireless Audio with Dock to a Bluetooth compatible 2012 Samsung TV (SoundShare) DOCK ● connections Connect <To pair to your TV> To produce TV sound on your Wireless Audio with Dock via Bluetooth connection, you need to pair your system to the Bluetooth compliant TV first. Once the pairing is established, the pairing information is recorded and kept and no further Bluetooth connection message will appear from the next time. Keep the Wireless Audio with Dock and the TV close together before pairing. (It is recommended to pair devices within 1 meter. ) 1. Turn on the Samsung TV and Wireless Audio with Dock. • Set "Add New Device" menu to "On" in the TV. (For more information, refer to the user's guide of TV) Menu ; System ; Device Manager ; SoundShare Settings ; Add New Device. [. . . ] ) button of the remote VOL BASS VOL BASS 2. Press MUTE ( ) on the remote control again (or press VOLUME +/-) to restore the sound. FUNCTION FUNCTION Using the BASS function MUTE Lets you optimise the bass sound according to your tastes. • Each time the button is pressed, the selection changes as follows : BASS ON ; OFF MUTE VOL BASS VOL BASS 29 SOFTWARE UPGRADE (only USB mode) 1. Visit www. samsung. com. DOCK 2. Click SUPPORT on the top right of the page. 3. Enter the product's model number into the search field, and then click Find Product. DC 14V 4A WPS/ RESET PUSH LAN AUX IN ONLY FOR SERVICE 4. Click Get downloads in the Center of the page below the Downloads header. 7. Once popup window appears, click OK and continue to download and save upgrade file onto your PC. [. . . ]