User manual ONKYO TX-82
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ONKYO TX-82. We hope that this ONKYO TX-82 user guide will be useful to you.
Manual abstract: user guide ONKYO TX-82
Detailed instructions for use are in the User's Guide.
[. . . ] Please retain this manual for future reference.
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Important Safeguards
1. [. . . ] Message area This area of the display shows various information about the currently selected source.
H
B
I
C
J
K
D E F
7
Front & Rear Panels--Continued
Rear Panel
1
2
3
4
5
6
AM
REMOTE CONTROL
ANTENNA
GND FM 75
SPEAKERS
R
IN IN
OUT
L AC OUTLET
IN
OUT
IN
A L L B R R
A
AC 120V 60Hz SWITCHED 120W 1A MAX.
B
PHONO
CD
TAPE 1
TAPE 2
78
9
J
A Grounding screw (14)
This screw is for connecting a turntable's ground wire. AM ANTENNA (12, 13) These push terminals are for connecting an AM antenna. SPEAKERS A (11) These lever terminals are for connecting speaker set A. SPEAKERS B (11) These lever terminals are for connecting speaker set B. (15) These (Remote Interactive) jacks can be connected to the jacks on other Onkyo CD player and cassette recorder. The TX-82's remote controller can then be used to control those components. Note: To use , you must make an analog audio connection between the TX-82 and the other component. can only be used with Onkyo components.
G PHONO IN (14)
These jacks can be used to connect a turntable with a moving-magnet cartridge. H CD IN (14) These jacks can be used to connect a CD player with an analog output. I TAPE 1, 2 IN/OUT (14) This analog audio input and output can be used to connect a cassette recorder, CD recorder, or other recorder with an analog input and output. J AC OUTLET (15) This switched AC outlet can be used to supply power to another component.
B
C D
E
F
8
Remote Controller
1 2 3 4 5
POWER
SLEEP
6
TAPE-1
INPUT SELECTOR TUNER PHONO
CD
TAPE-2
DECK-A
DECK-B
GROUP
TUNER PRESET
MUTING
7 8
CD
DISC
VOLUME
REMOTE CONTROLLER RC-330S
A POWER button (16)
This button is used to set the TX-82 to On or standby. · The impedance of each speaker connected to this unit must be no lower than 4 ohms. If you're using only speakers A or speakers B, the minimum speaker impedance is 4 ohms. If you're using both speakers A and speaker B, the minimum speaker impedance is 8 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated. · Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided. · Don't connect more than one cable to each speaker terminal. Doing so may damage the TX-82.
A B
· If you want to connect a single speaker instead of a pair, connect it to either the left or right speaker terminals, not both.
NO!
R L
A
A
NO!
R L
A
A
1
Strip 3/8" (10 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly. Push the lever to open the hole, insert the bare wire into the hole, and then push the lever again to close the hole, thereby securing the wire.
3/8" (10 mm)
2
Maker sure that the speaker connectors are gripping the bare wires, not the insulation.
The following illustration shows which speakers should be connected to which terminals.
Speaker set A
Right speaker Left speaker
SPEAKERS
R
L
AM
REMOTE CONTROL
A
A
ANTENNA
GND FM 75
SPEAKERS
R
IN IN
OUT
L AC OUTLET
B
B
IN
OUT
IN
A L B
A
L
AC 120V 60Hz SWITCHED 120W 1A MAX.
B
R
R
PHONO
CD
TAPE 1
TAPE 2
CAUTION: SPEAKER IMPEDANCE A or B: 4 ohms min. /speaker A + B: 8 ohms min. /speaker
Right speaker
Left speaker
Speaker set B
11
Connections--Continued
Connecting the Supplied FM & AM Indoor Antennas
ANTENNA
AM
REMOTE CONTROL
ANTENNA
GND FM 75
SPEAKERS
R
IN IN
OUT
L AC OUTLET
IN
OUT
IN
A L L B R R
A
AC 120V 60Hz SWITCHED 120W 1A MAX.
B
PHONO
CD
TAPE 1
TAPE 2
Adjusting the Position of the FM Indoor Antenna
The FM indoor antenna is for indoor use only. Extend the antenna fully and point it in various directions to find the best reception. If the reception is not very good with the supplied FM indoor antenna, use an outdoor antenna.
1 Strip the insulation from the end of the wire. 2 Fully insert the bare wire.
GND FM 75
AM
ANTENNA
Adjusting the Position of the AM Indoor Antenna
The AM loop antenna is for indoor use only. [. . . ] · Make sure that the power cord is properly plugged into the wall outlet. · Unplug the power cord from the wall outlet, wait five seconds or more, then plug the cable in again. Remove the power cord from the wall outlet immediately and contact your Onkyo dealer.
Audio
There's no sound, or it's very quiet?· Make sure that all audio connecting plugs are pushed in all the way (pages 1115). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ONKYO TX-82
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ONKYO TX-82 will begin.