User manual ONEFORALL URC 7140

[. . . ] Macro on "red key" OFF STOP & OFF page 4 1 2 3 and and and mm Comm Comm Co DVD Macro on "red key" = command 1: dvd STOP command 2: dvd OFF command 3: tv OFF · What is my "Set Up Code again? Find out which code is currently set under each of the 4 device modes. 1 My Code is? 5 page 5 1556 5 6 Mode Reassignment This feature gives you the possibility to program 2 (or more) of the same device types onto the ONE FOR ALL remote (e. g. Therefore we will reassign (change) "sat" mode into "tv" mode. TV2 Philips + 4 TV1 Sony Press and release the magic key. 5 < select > Select the destination device e. g. How to reassign "sat" into "tv" so you can control your second televion as well: 3 sec. 1 3 sec. Press and release the magic key. --> The blue LED will blink twice. Congratulations! [. . . ] You can request your function codes through our consumer service help-line or by letter, fax or e-mail. 2 When you contact us please make sure to mention the following: · The Current code you are using (see "What is my Set Up Code again?" ) · Device-type, Brand & Model-number of the corresponding device. · How the function was labeled on your original remote control. then; Customer Service will provide you: · A funcion-code (5-digit) for every requested function. Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit. 3 sec. 3 Once you obtain your function code(s) from customer service, programming the code is easy: x2 Example: How to get the "I/II (mono/stereo)" function from your original LOST or BROKEN remote onto the "red key" on your ONE FOR ALL remote control. --> The blue LED will blink twice. 4 Press and release the magic key. 5 Key Ma gic ® Enter the 5-digit function-code provided by Customer Service. Original LOST or BROKEN remote 6 Press the key to which the function will be assigned (e. g. red key). --> The blue LED will blink twice. 1 < select > Congratulations!You have successfully programmed the "I/II (mono/streo)" function from your original remote control onto your ONE FOR ALL remote control. NOW whenever you press the "red key" (in tv mode) you will obtain the "I/II (mono/streo)" function. Select the source device e. g. 2) Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit. red) twice. 3 Macro You can program your ONE FOR ALL to issue a sequence of commands at the press of one single key. Any sequence of commands you regularly use can be reduced to one key press for your convenience. For example, you may want to create the following macro: 1st command: 2nd command: 3rd command: dvd --> STOP dvd --> OFF tv --> OFF To set up the Macro mentioned above on the e. g. "Red" key on your ONE FOR ALL: 1 3 sec. 7 < select > Select the corresponding device e. g. TV Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit. 8 2 Press the POWER key x2 Press 9 9 5. --> The blue LED will blink twice. 9 3 Press the key to which the function will be assigned (e. g. [. . . ] You have successfully blinked out your current Set Up Code in tv mode. < select > Select the corresponding device e. g. TV 3 x2 Press 9 9 0. --> The blue LED will blink twice. Your "Set Up Codes" : 4 ?? Press 1 for the 1st digit of your 4-digit set up code and count how many times the LED blinks. If the LED does not blink, the digit is "0". 5 ?? Press 2 for the 1st digit of your 4-digit set up code and count how many times the LED blinks. If the LED does not blink, the digit is "0". 6 Operational Reset ?? The Operational reset will erase all learned functions across all modes and some other programmed functions like Key Magic and Macros. [. . . ]