User manual ONEFORALL URC 3605

[. . . ] If the batteries are inserted correctly, the LED will blink once. NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 10 minutes to ensure all of your programming information is restored. PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. [. . . ] As before, write down each fourdigit code. SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: Changing channels does not work properly. To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SETUP until the LED blinks twice, then release SETUP. Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. USER'S GUIDE VOL ­ VOL + Use VOL+ (or VOL-) to raise (or lower) the sound volume. Use CH+ (or CH -) to select the next higher (or lower) channel. SKIP FWD CH INTRODUCTION The One For All Access 3 Universal Remote Control is designed to operate three home entertainment devices, depending on the model purchased (see Key Charts, Mode Keys on the right). The remote control requires two fresh AAA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. 1. Turn on a device (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. RE-ASSIGNING DEVICE KEYS The One For All Access 3 can be set to control a second TV, VCR, or DVD player. For example, to control two TVs, a VCR, and a cable box, you will need to reassign the unused DVD key to operate the second TV as follows: 1. On the remote control, press and hold SETUP until the LED blinks twice, then release SETUP. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. PROBLEM: Tried "Search Method" and still could not find a working code. CH SKIP FWD SHIFT CH CH SKIP REV When controlling a DVD player, use SKIP FORWARD to next DVD chapter. , use SKIP REVERSE to the last DVD chapter. Press SHIFT and use the Up/Down/Left Right cursor keys to move the cursor in the program guide and menu screens. Press SHIFT and MUTE to select a menu item. Unlocking Volume Control: NOTE: Perform these instructions when you want independent volume control for each programmed device (e. g. , TV volume control in TV mode, CBL/SAT volume control in CBL/SAT mode, etc. ) SHIFT 2. On the remote control, press a device key once (i. e. , VCR/DVD, TV, or CBL/SAT ). Use the Manufacturer's Codes to locate the type of device and brand name and then enter the first fourdigit code for your component. [. . . ] Volume will again be controlled according to its default states. FEATURES AND FUNCTIONS Use the Key Charts to learn how to use the universal functions of the One For All Access 3 Universal Remote Control. SLEEP SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. Key Charts SET Press SLEEP to activate your device's sleep timer (not available for all devices). PLAY FF Use SETUP for all programming sequences. The LED (red light) blinks to show that the remote control is working and is sending signals. REW REC PAUSE STOP Use the transport keys to control your VCR, CD or DVD player, or VOD. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. [. . . ]