User manual ONE DSD 660

[. . . ] 15 Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Digital Satellite Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect a second SCART to SCART connector between the VCR SCART connector on the decoder and the TV SCART on the second decoder. 6 RCU UHF Button Selection Functions Pressing UHF on the RCU with the second decoder connected and operating, selects the TV viewing source in the sequence VCR, AU1, TV and IRD. If AU1 is selected, the satellite picture is routed to the TV and VCR from the second decoder. If a second satellite decoder is being used, consult the installer as to the menu setup requirements. NOTE: 2 Using a SCART-to-SCART cable (not supplied), connect the TV SCART socket on the decoder to the SCART socket on the TV. If the TV does not have a SCART connector, use the supplied flylead to connect the RF OUT socket of the decoder to the RF IN socket on the TV. Connect the coaxial cable connector from the LNB on the satellite dish into the socket marked LNB IN on the decoder. The connector on the coaxial cable should be turned until it is finger tight 3 4 12 OPERATING INSTRUCTIONS DSD 660 Bouquet Selection The TV services are transmitted in packages called BOUQUETS, each bouquet containing a series of services or programmes . The decoder has provision for several bouquets, any of which can be selected by pressing TV on the RCU, highlighting the required bouquet using the up/down arrows on the RCU , then following the on-screen instructions. If a selected bouquet is not subscribed to, a message "E38 Service is not currently running" will appear on the TV screen. When a subscribed to bouquet is selected, the services in that bouquet will be listed numerically in the Electronic Programme Guide (see page 15). Stepping through Services Stepping through services is possible using either the RCU or decoder front panel keys. Stepping using the RCU To step through services using the RCU, do the following: 1 2 Select the type of service required, TV or audio ( ) Press P+ to step to the next service or P - to step to the previous service in the list of available services. After pressing P+ or P -, an information box is displayed at the bottom of the TV screen with details of the service. After a few seconds, the relevant service is displayed/heard. Bouquet Selection Middle East Programmes 3 If required, continue stepping by pressing P+ or P - until you find the service you prefer. It is not necessary to wait for services to be displayed/heard before stepping to the next or previous service. If you decide to watch or listen to a service you have stepped to, wait for the service to be displayed/heard. The information box will disappear after a short while or can be removed immediately by pressing EXIT. Press OK to select Press EXIT to cancel Selecting Specific Services Specific TV or Audio Services can be selected, either: NOTE: When you reach the last available service in the list and press P+ you are returned to the first service in the list. TIP: Use the convenient selecting and sorting facilities to personalise the services list. After using these facilities, your favourite services will be in your order of preference. Stepping using the Decoder Front Panel Keys # # Directly, using the RCU By stepping through services using the RCU or decoder front panel keys By using the Open TV Electronic Programme Guide (EPG), or By using the Open TV Information Bar. 2 To step and select a specific service using the decoder front panel keys, do the following: 1 Select the type of service required, by pressing TV/ to switch between TV services and audio services. Selection of the audio service is indicated by a green indicator on the front panel display. Press (up) to step to the next service or (down) to step to the previous service in the list of available services. After pressing or , an information box is displayed at the bottom of the TV screen with details of the service. [. . . ] Where possible, the errors will be communicated via messages on the TV screen and/or the decoder display panel. Locate either the corresponding error number and message or the description of your problem in the troubleshooting table and follow the advice provided. If you have tried the appropriate remedy and still have difficulty in operating your decoder, please call the appropriate hot line. 2 3 Press OK. The Upgrade screen is displayed with the message "Checking for upgrade". [. . . ]