User manual OMRON WS02-LCTC1-EV5 V5.2 REV 12-2008

[. . . ] W372-E1-12 SYSMAC CS/CJ Series WS02-LCTC1-EV5 CX-Process Tool Ver. 5. 2 Operation Manual Revised December 2008 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Failure to heed precautions can result in injury to people or damage to property. [. . . ] (All characters can be used. ) 0 to 127 0 to 32 16 to 31, 225 0 to 1, 000 0 to 1, 000 Input automatically. Note a) When the CX-Server is selected, the node address must be set to a number other than 0 before compiling the SCADA software CSV tag file. The editing results will be automatically reflected in the CSV tag list. The CSV tag list is displayed by selecting Show Tag List/ CSV Tag from the Execution Menu. As required, use the setting method provided under Setting Tags Individually Using the CSV Settings Dialog Box on page 145 to individually edit the function block CSV tags. Step 3: Checking CSV Tags Check the CSV tag settings by selecting Show Tag List/CSV Tag from the Execution Menu. The following dialog box will be displayed. Step 4: Creating SCADA Software or RS View Tag Files (Compiling) Compile the CSV tag file or the RS View tag file using the following procedure after setting the CSV tags. Note When CX-Server has been selected as the communications driver, set the node address to a non-zero value in the Change PLC Dialog Box before compiling the CSV tag file. (If the computer is connected online, return the node address setting to 0. ) The following conditions must be met to compile the SCADA or RS View tag file: 1) CSV tags must be set for Control, Operation (except internal switches), and External Controller Terminal Blocks, and both Send All Blocks (462) and Re- 149 Using SCADA Software Section 3-4 ceive All Blocks (461) must be registered for Loop Control Units and 2) CSV tags must be set for any Expanded CPU Unit Terminal function blocks for Loop Control Units. Creating SCADA Tag Files 1) Select Compile CSV Tags from the Execution Menu. The following dialog box will be displayed. If Check Errors is selected and the OK Button is clicked, the results of the error check will be displayed when the file is compiled. To add user link table tags to the CSV tag file for LCBjjs, select Add User Link Table Information. Error Display The following dialog box will be displayed for confirmation. Click the Cancel Button and correct the error. (For example, if the message says a CSV tag is not registered for a certain block address, register the CSV tag. ) If the OK Button is pressed even though there is an error, the same dialog box as for when no error occurs will be displayed. 150 Using SCADA Software Section The following window will be displayed if there are no errors. 3-4 3) Set the folder and name for the CSV tag file and click the Save Button. The following dialog box will appear if CSV tag file was compiled correctly. 4) Click the OK Button. The following dialog box will be displayed. If Check Errors is selected and the OK Button is clicked, the results of the error check will be displayed when the file is compiled. Note a) When adding user link table tags to the RS View tag file, select the option to output CSV tag information in either the Edit User Link Table Dialog Box or the User Link Table Batch Registration Dialog Box when registering the user link table and then enable adding user link table information when compiling. b) If a user link table is created without enabling outputting CSV tag information, the user link table tags will not be output even if adding user link table information is selected. The results will be displayed in the Output Window. 151 Using SCADA Software Error Display Section 3-4 Normal Display 152 Using SCADA Software Section 3-4 3. The following RS View Tag Compile Dialog Box will appear. When specifying a SCADA tag file (Taglist. csv) for compilation, select this option and specify the SCADA tag file. If this option is selected: The OPC Server group name will be the same as the CSV tag file tag name (representative tags) and the OPC Server tag name will be the same as the CSV tag file ITEM tag name. If this option is not selected: The OPC Server tag name will be the same as the CSV tag file tag name (representative tags) and the ITEM name will be added after an underscore. Select this option to add the symbol information for the symbols for all local symbol tables in the current CXP project for CX-Programmer running on the same computer. [. . . ] Select all of the data in the column to be moved, and then right-click and select Move Column from the pop-up menu. When Move Column is selected, the cursor is changed to · Multiple columns can be selected and moved. The column will move when selected in this state. 335 Setting Segment Programs Transfer to LC Used to transfer the data in selected cells to the Loop Controller. · Multiple cells or columns can be selected and transferred. Appendix C Note Be sure to check the safety of all equipment before making a transfer while the Loop Controller is operating. 336 Appendix D Sequence Table Design Sheet A sequence table design sheet is provided below. [. . . ]