User manual OMRON S82J

[. . . ] Switch Mode Power Supply S82J (10/25/50/100/150/300/600-W Models) Low-cost Global Power Supply with CE Marking · Safety standards: UL: UL508, No. 60950-1 Class 2, CSA: cUL: C22. 2 No. 14, cUR: 60950-1 Class 2, EN60950-1 (=VDE0805 Teil 1), EN50178 (=VDE0160) · EMC: Conforms to EN61204-3 Class A · Mounting bracket available for standard models Front-mounting bracket type DIN Rail mounting type (except 300 W and 600 W) Note: Refer to Precautions for Safe Use on page 17. Model Number Structure Model Number Legend Note: Not all combinations are possible. Please refer to the list of models in Ordering Information on pages 2 and 3. S82J 1 1. Power Ratings 010: 10 W 025: 25 W 050: 50 W 100: 100 W 150: 150 W 300: 300 W 600: 600 W 2. [. . . ] Internal parts may occasionally deteriorate or be damaged if a short-circuited or other overcurrent state continues during operation. In actual operation, the output voltage may not fall to 0 V when the overload protection function is triggered. Even with short-circuits on the load side, the drop in voltage will vary depending on factors such as the impedance in the load line. The overload protection function is activated at 105% of the rated output current for 300-W models. Inrush Current, Startup Time, Hold Time Input ON AC input voltage Input OFF 600-W Models Output voltage (V) Inrush current on input application AC input current 90% Output interrupted 0 50 100 Output current (%) 96. 5% Output voltage Startup time Hold time (20 ms min. ) 10 Switch Mode Power Supply S82J Dimensions Note: All units are in millimeters unless otherwise indicated. Open-frame type and covered type have the same dimensions. Front-mounting Bracket Type S82J-01090±1 Mounting Holes (Surface Screw Mounting) Side Mounting 8. 2 9. 5 Output indicator (Green) Output voltage adjuster +V DC output terminal -V Earthing terminal PE AC (L) Input terminal AC (N) +V -V AC AC 3. 5 Two, M3 97±1 65±0. 5 3. 5 dia. 65±0. 5 82±0. 5 Five, M3. 5 Nameplate 5 82±0. 5 5 Bottom Mounting 6. 5 3. 5 dia. 78±0. 5 Two, M3 17. 5 15 50±0. 5 3. 5 Two, M3 1 28 35± 78±0. 5 S82J-025124±1 3. 5 Mounting Holes (Surface Screw Mounting) Side Mounting Two, M3 +V 9. 5 8. 2 Output indicator (Green) Output voltage adjuster DC output terminal +V -V Earthing terminal PE AC (L) Input terminal AC (N) -V AC AC 97±1 65±0. 5 Five, M3. 5 Nameplate 65±0. 5 3. 5 dia. 116±0. 5 5 6. 5 3. 5 dia. Three, M3 17. 5 21. 5 83±0. 5 28 40±1 116±0. 5 112±0. 5 6 3. 5 Bottom Mounting Two, M3 112±0. 5 S82J-050161±1 3. 5 9. 5 8. 2 Output indicator (Green) Output voltage adjuster +V Mounting Holes (Surface Screw Mounting) Side Mounting Two, M3 97±1 65±0. 5 DC output terminal Five, M3. 5 Nameplate +V -V Earthing terminal PE AC (L) Input terminal AC (N) -V AC AC 65±0. 5 3. 5 dia. 153±0. 5 5 6. 5 3. 5 dia. Three, M3 10 22 127±0. 5 153±0. 5 150. 5±0. 5 7 20±0. 5 3. 5 Bottom Mounting Two, M3 28 40±1 20 150. 5±0. 5 Switch Mode Power Supply S82J 11 S82J-10024@ (100 W, 24-V Output) 9. 5 8. 2 12 max. 170±1 4. 5 Mounting Holes (Surface Screw Mounting) Side Mounting Two, M4 Output indicator (Green) Output voltage adjuster DC output terminal Earthing terminal +V -V PE AC (L) AC (N) +V 97±1 65±0. 5 4. 5 dia. -V AC AC 65±0. 5 Five, M3. 5 Nameplate Input terminal 162±0. 5 162±0. 5 160±0. 5 4. 5 7 5 6. 5 4. 5 dia. 27. 5 15 Three, M4 Bottom Mounting Two, M4 50±1 28±0. 5 25±0. 5 160±0. 5 100±0. 5 15 S82J-100@ (100 W, 5-/12-/15-V Output) S82J-15024@ (150 W) 198 (see note) 188 4 max. Mounting Holes (Surface Screw Mounting) Side Mounting Two, M4 4. 5 8. 1 9. 5 89±0. 5 97 82±0. 8 180±0. 5 7±0. 3 4. 5 dia. 180±0. 5 3±0. 25 M4 × 8 Bottom Mounting Two, M4 Mounting holes (on both sides) 4. 5 dia. 178±0. 5 3±0. 25 178±0. 5 4. 5 27. 5±0. 3 25±0. 5 50 35±0. 3 15 Three, M4 (6 max. deep) 100±0. 5 55±0. 3 S82J-30024@ (300 W) Nine, M4 terminal screws DC ON POWER SUPPLY V. ADJ INPUT 50/60Hz AC100-120V 8A AC200-230V 4A 4 (19) 181±1 Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting 10 OUTPUT DC24V 14A +V L N Side OPERATION 8. 6 ALM 92±1 -V VOLTAGE SELECT SHORT 100-120V OPEN 200-230V 50±0. 5 Four, 4. 5 dia. 21 SHORT BAR OMRON Corporation MADE IN JAPAN PARALLEL SINGLE 50±0. 5 120±1 19 150±0. 5 Four, M4 holes (depth: 8 max. ) 10 150±0. 5 Bottom Mounting Four, 4. 5 dia. 100±0. 5 100±0. 5 19 150±0. 5 150±0. 5 12 Switch Mode Power Supply S82J S82J-60024@ (600 W) Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting Four, 4. 5 dia. Four, M4 holes (depth: 8 max. on one side) Four, M4 holes (depth: 8 max. ) 150±0. 5 50±0. 5 Nine, M4 terminal screws Bottom Mounting Four, 4. 5 dia. 100±0. 5 150±0. 5 Dimensions with Mounting Brackets (Provided) For 10-/25-/50-/100 (24 V)-W Models Front-mounting Bracket (Provided) 1. 5 9 Two, 3. 5 dia. 11 4. 6 15±0. 2 Mounting Holes Using the Mounting Bracket Attach the mounting bracket to the panel and loosely tighten the two screws. Insert the projected parts of the bracket (b) to the square holes of the power supply (a). Then securely tighten the screws. 60 74 60 Two, M3 Note: The mounting screws must be ordered separately. 4. 6 11 5 20 31. 5 4. 7 15 t=1. 0 20. 5 (a) Power supply unit Mounting bracket 20 (b) Material: Stainless steel (b) (a) For 100- (5, 12, 15 V) and 150-W Models Front-mounting Bracket (Provided) 6. 5 11 5 dia. [. . . ] Refer to Dimensions on page 11. Mounting brackets (provided) Metal plate Series Operation Only models with power ratings of 50, 100, 150, 300, or 600-W allow series operation. +V INPUT -V VL +V INPUT -V D2 V2 VL= V1 + V2 D1 V1 Model: S82Y-JFAN Fan Set: Fan (above), four M4 x 35 sems screws, instruction sheet, and packing case Replace the fan as shown in the following illustration. Model S82J Output capacity 100 W 50, 150, 300, 600 W Rated output voltage 5, 12, 15, 24 VDC 24 VDC Up to two of the above Power Supplies can be used in series operation. Models other than the above Power Supplies cannot be used in series operation. If series operation is attempted for other models, the output from one of the Power Supplies may not come ON when the AC input is applied. If that occurs and the Power Supplies are left in that state, internal circuits may be damaged. [. . . ]