User manual OMRON H3Y DATASHEET

[. . . ] Solid-state Timer Miniature Timer Compatible with the MY Relay Large transparent time-setting knob facilitates time setting. Flat-blade and Phillips screwdrivers can also be used for time setting. High repeat accuracy. H3Y RC Ordering Information Operation/resetting Ope a o / ese g t system Time-limit operation/ e o ea o / self-resetting lf tti Time-limit contact e co ac Time ranges e a ges Supply voltage Supp y o age Model Surface /DIN-track mounting (with socket) DPDT 0 0. 1 s to 30 min o 110 VAC 220 VAC 24 VDC 4PDT 110 VAC 220 VAC 24 VDC Note: Specify the model number, supply voltage, and rated time when ordering. [. . . ] 6. 3 28 max. 6. 4 (63. 0) Accessories (Order Separately) Use the PYFjA, PYj, PYj-02, or PYjQN(2) to mount the H3Y. When ordering any one of these sockets, replace "j" with "08" or "14. " Track Mounting/Front Connecting Sockets PYF08A Two, 4. 2 × 5 mounting holes 6 Eight, M3 × 8 sems 3. 4 Terminal Arrangement (Top View) Mounting Holes Two, 4. 5 dia. 16. 5 30 max. PYFjA 15±0. 2 PYF14A Two, 4. 2 × 5 mounting holes 6 3. 4 Fourteen, M3 × 8 sems Terminal Arrangement (Top View) Mounting Holes Two, 4. 5 dia. 6 22±0. 2 4 H3Y PYF08A-N 22 max. H3Y Terminal Arrangement 42 4 44 8 12 1 14 5 Mounting Holes (for Surface Mounting) 4 42 8 44 1 12 5 14 3. 2 dia. 19. 8 3. 6 dia. PYF-08A-N 41 12 11 9 12 41 14 9 11 14 13 A2 A2 A1 14 14 13 A2 A2 A1 30 max. PYF14A-N Terminal Arrangement 4 42 8 44 3 32 7 34 2 22 6 24 1 12 5 14 42 32 22 12 4321 44 34 24 14 8765 Mounting Holes (for Surface Mounting) Two, 3. 5 dia. 66. 5 max. PYF-14A-N 41 12 31 11 21 10 11 9 20. 8 12 11 10 9 41 31 21 11 14 14 A2 A2 13 A1 A2 14 A2 14 A1 13 30 max. 29. 5 max. PYF08A-E Two, 4. 2 × 5 mounting holes Eight, M3 × 8 sems (Top View) Two, 4. 5 dia. 31 max. PYF14A-E Two, 4. 2 × 5 mounting holes Eight, M3 × 8 sems (Top View) Two, 4. 5 dia. 31 max. 5 H3Y Back Connecting Sockets PY08, PY14 Eight, 3 × 1. 2 dia. 2. 6 29. 5 max. H3Y Terminal Arrangement (Bottom View) Panel Cutout 21. 4 0 +0. 2 59. 3 25. 8 +0. 2 0 H3Y Series 2. 7 20 max. 7. 7 PY08 PY14 PYj, PYj-02, PYjQN(2) PY08QN, PY14QN PY08QN(2), PY14QN(2) 2. 7 25 max. 22 max. Terminal Arrangement (Bottom View) 29. 5 max. ** 41. 5 max. (see note) Note: 1x1 PY08QN PY08QN(2) PY14QN PY14QN(2) With PYjQN(2), dimension * should read 20 max. 2 Terminal Arrangement (Bottom View) 2. 7 16. 5 max. 4. 3 PY08-02 PY14-02 6 H3Y Socket Mounting Plates (t = 1. 6) Applicable socket PY08, PY14, PY08QN(2), PY14QN(2) Note: PYP-1 Two, 3. 4-dia. holes H3Y For mounting 1 socket PYP-1 For mounting 18 sockets PYP-18 PYP-18 may be cut to any desired length. PYP-18 Relay Hold-down Clips Y92H-3 for PYFjA Socket Y92H-4 for PYj Socket Mounting Track PFP-100N/PFP-50N (see note 1) End Plate PFP-M 1000 (500) (See note 2) Note: 1. This dimension applies to PFP-50N. Spacer PFP-S 7 H3Y H3Y Installation Connection H3Y-2 H3Y-4 Connect the DC power supply to terminals 13 and 14 according to the polarity marks. Connect the DC power supply to terminals 13 and 14 according to the polarity marks. Precautions When selecting a control output, use the H3Y-2 for switching ON and OFF the power and the H3Y-4 for switching ON and OFF the minute load. [. . . ] The internal parts may become damaged if a supply voltage other than the rated ones is imposed on the H3Y. When more than 100 V is applied to 12 or 24 VDC, the internal element (varistor) may break. Do not connect the H3Y as shown in the following circuit diagram on the right hand side, otherwise the H3Y's internal contacts different from each other in polarity may become short-circuited. Correct Incorrect Limited issue for Southeast Asian countries ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. L097-E1-1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Supervisory Control Devices Division 28th Fl. , Crystal Tower Bldg. , 1-2-27, Shiromi, Chuo-ku, Osaka 540-6028 Japan Phone: (81)6-949-6035 Fax: (81)6-949-6069 Printed in Japan 0597-2M (0597) a 8 [. . . ]