User manual OMRON E3S-A DATASHEET

[. . . ] 16 mA) External diagnostic input Input Voltage --With emitter OFF: NPN: 0 V short-circuit or 1. 5 V max. with 0. 1 mA current leakage) 0. 5 ms max. Response time Ambient illumination Ambient temperature Ambient humidity Insulation resistance Dielectric strength Vibration resistance Shock resistance Enclosure ratings Incandescent lamp: Sunlight: Illumination on optical spot: 5, 000 lx max. Illumination on optical spot: 10, 000 lx max. Operating: ­25°C to 55°C (with no icing) Storage: ­40°C to 70°C (with no icing) Operating: 35% to 85% Storage: 35% to 95% 20 MW min. (at 500 V DC) 1, 000 V AC, 50/60 Hz for 1 min Destruction: 10 to 55 Hz, 1. 5-mm double amplitude (30G) 2 hrs each in three directions Destruction: Approx. [. . . ] (The photoelectric sensor, however, will not malfunction even if the turbo function is switched on for more than 3 mins. ) With Turbo Switch ON The turbo function is effective with the turbo switch pressed, and the function is reset automatically when released. E3S-A Normal Operating Condition Adjustor cap PUSH Sensitivity adjustor The OFF-delay time adjustor is used as a turbo switch (black) Operating Mode Selection As shown in the following illustration, the E3S-A has an operating mode selector on the panel where the Receiver connector is located. With this operating mode selector, the E3S-A is in either dark-ON or light-ON mode. Operating mode selector (black) Dark-ON Light-ON E3S-A A-243 Dimensions Sensors Prewired Type E3S-AT11, E3S-AT31 (Receiver) Light indicator (red) 7 Sensitivity adjustor (white) (4) 40 12. 9 Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 Mounting Holes 16. 9 10. 7 16. 5 Two, M3 holes 3. 2 7. 2 3. 2 Stability indicator (green) 10. 5 Lens (7 x 7) Optical axis 4. 8 5 20 30 7. 2 Two mounting holes 20 Mode Selector (black) Dark-ON Light-ON 1. 3 21 8 5. 5 16. 2 A (see note) 1. 2 10. 7 29. 2 D L A (see note) Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AT11, E3S-AT31 (Emitter) 40 17. 8 Light indicator (red) (4) Polyvinyl chloride-covered cord , 4-mm dia. (0. 12-mm x 18), 2 cores, Standard length:2 m 12. 4 12 16. 9 10. 7 16. 5 3. 2 7. 2 Mounting Holes Two, M3 holes 3. 2 4. 8 5 10. 5 Lens (7 x 7) Optical axis 20 30 7. 2 20 Two mounting holes Mode Selector (black) Dark-ON Light-ON 1. 3 D L 21 8 A (see note) 5. 5 16. 2 1. 2 10. 7 A (see note) Two, M3 x 12 screws 29. 2 Note: The mounting bracket can be attached to side A. A-244 Standard Photoelectric Sensors E3S-AT21, E3S-AT41 (Receiver) 12. 9 7 12. 4 12 Mounting Holes 16. 9 10. 7 16. 5 Two, M3 holes 3. 2 7. 2 Stability indicator (green) 10. 5 Lens (7 x 7) Optical axis 3. 2 4. 8 5 20 30 7. 2 20 Two mounting holes Mode Selector (black) Dark-ON Light-ON 1. 3 21 8 5. 5 1. 2 10. 7 16. 2 29. 2 D L A (see note) A (see note) Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AT21, E3S-AT41 (Emitter) Light indicator (red) 12. 9 40 12. 5 Turbo Switch (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 2 cores, Standard length:2 m 12. 4 12 16. 5 10. 7 16. 5 3. 2 7. 2 Mounting Holes Two, M3 holes 3. 2 4. 8 5 10. 5 Lens (7 x 7) Optical axis 20 30 7. 2 Two mounting holes 20 Mode Selector (black) Dark-ON Light-ON 1. 3 D L 27 8 A (see note) 5. 5 16. 2 1. 2 10. 7 A (see note) 29. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-A A-245 E3S-A Light indicator (red) Sensitivity adjustor (white) Time adjustor (black) (4) 40 2-m polyvinyl chloride-covered cord, 5. 5 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m E3S-AR11, E3S-AR31 E3S-AR21, E3S-AR41 Sensitivity adjustor (white) Light indicator (red) 42. 3 15. 2 2. 3 7 5. 5 OFF-delay time adjustor/turbo switch (black) (see Note 1) Turn to adjust the OFF-delay time: push to switch turbo function ON (4) (see note 2) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 5 cores (9) (E3S-AR21, -41), 3 cores (E3S-AR11, 31), Standard length: 2 m 12. 4 12 16. 9 10. 7 16. 5 3. 2 7. 2 Note: 1. 9 mm for E3S-AR21 and E3S-AR41 Mounting Holes Two, M3 holes 3. 2 4. 8 5 20 10. 5 30 Mode Selector (black) Dark-ON Light-ON 1. 3 7. 2 Stability indicator (green) Two mounting holes 20 Lens (7 x 14) Receiver Optical axis D L 21 11. 5 9 19. 7 Emitter A (see note) 1. 2 10. 7 A (see note) 29. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AD11, E3S-AD31 E3S-AD13, E3S-AD31 E3S-AD12, E3S-AD32 Light indicator (red) 40 12. 9 7 Sensitivity adjustor (white) (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 3 cores, Standard length: 2 m 12. 4 12 16. 9 10. 7 16. 5 3. 2 7. 2 Mounting Holes Two, M3 holes Stability indicator (green) 10. 5 Lens (7 x 14) Receiver Optical axis 3. 2 4. 8 5 20 30 7. 2 Two mounting holes 20 Mode Selector (black) Dark-ON Light-ON 1. 3 D L 21 11. 5 1. 2 Emitter A (see note) Two, M3 x 12 screws 9 19. 7 10. 7 A (see note) 29. 2 Note: The mounting bracket can be attached to side A. A-246 Standard Photoelectric Sensors Light indicator (red) 40 12. 9 7 (4) 5. 5 Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 16. 9 16. 5 Note: Turbo switch is only for E3S-AD21 and E3S-AD41. 10. 7 3. 2 7. 2 Mounting Holes Two, M3 holes Stability indicator (green) Lens (7 x 14) 10. 5 Receiver Optical axis 1. 3 3. 2 4. 8 5 20 30 7. 2 Two mounting holes 20 Mode Selector (black) Dark-ON Light-ON D L 21 11. 5 1. 2 10. 7 A (see note) 9 19. 7 Emitter A (see note) Two, M3 x 12 screws 29. 2 Note: The mounting bracket can be attached to side A. E3S-AT61, E3S-AT81 (Receiver) Lens (7 x 7) 13. 5 Optical axis 40 8. 3 (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 Use these two holes for mounting. 10. 7 16. 5 7. 2 20 Four mounting holes Mode Selector (black) Dark-ON Light-ON 16. 9 Mounting Holes Two, M3 holes 20 3. 1 3. 6 41. 7 Stability indicator (green) 3. 6 7 21 29. 2 Light indicator (red) Sensitivity adjustor (white) 7. 2 1. 3 D L A (see note) A (see note) 1. 2 10. 7 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-A A-247 E3S-A E3S-AD21, E3S-AD41 E3S-AD23, E3S-AD43 E3S-AD22, E3S-AD42 OFF-delay time adjustor/turbo Sensitivity adjustor (white) switch (black) (see Note) Turn to adjust the OFF-delay time: push to switch turbo function E3S-AT61, E3S-AT81 (Emitter) Lens (7 x 7) 13. 5 Optical axis 40 8. 3 (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 Use these two holes for mounting. 10. 7 16. 5 7. 2 20 3. 1 3. 6 41. 7 Light indicator (red) 8. 5 21 29. 2 16. 9 Mounting Holes Two, M3 holes 7. 2 Four mounting holes 20 Mode Selector (black) Dark-ON Light-ON 1. 3 D L A (see note) 1. 2 10. 7 A (see note) 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AT71, E3S-AT91 (Receiver) Lens (7 x 7) 13. 5 Optical axis 40 8. 3 (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 16. 9 10. 7 16. 5 Use these two holes for mounting. Mounting Holes 7. 2 20 3. 1 3. 6 41. 7 Light indicator (red) Sensitivity adjustor (white) 3. 6 Time adjustor (black) 7 21 5. 5 29. 2 1. 3 Two, M3 holes 7. 2 Four mount ing holes 20 Stability indicator (green) Mode Selector (black) Dark-ON Light-ON D L A (see note) 1. 2 10. 7 A (see note) 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. A-248 Standard Photoelectric Sensors E3S-AT71, E3S-AT91 (Emitter) Lens (7 x 7) 13. 5 Optical axis 12. 4 12 16. 9 10. 7 16. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 3. 1 3. 6 41. 7 Four mounting holes 7. 2 20 Light indicator (red) 1. 3 3. 6 Turbo switch Mode Selector (black) Dark-ON Light-ON D L 21 12. 5 29. 2 A (see note) 1. 2 10. 7 A (see note) 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AR61, E3S-AR81 E3S-AR71, E3S-AR91 Receiver Lens (7 x 14) 13. 5 40 8. 3 Optical axis Emitter (4) (see note 2) (9) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 5 cores (E3S-AR71/-AR91), 3 cores (E3S-AR61/-AR81), Standard length: 2 m 12. 4 12 16. 9 10. 7 Use these two holes for mounting. 16. 5 7. 2 Mounting Holes Two, M3 holes 20 3. 1 3. 6 4. 7 7. 2 Four mounting holes 20 Stability indicator (green) Light indicator (red) Sensitivity adjustor (white) OFF-delay time adjus tor/turbo switch (black) (see note 1) Turn to adjust the OFFdelay time: push to switch turbo function 31. 5 Mode Selector (black) Dark-ON Light-ON 5. 9 7 23. 3 5. 5 D L A (see note 3) 10. 7 A (see note) 12 10. 5 1. 3 20+0. 8 Two, M3 x 12 screws Note: 1. The mounting bracket can be attached to side A. E3S-A A-249 E3S-A 40 8. 3 (4) Polyvinyl chloride-covered cord , 4-mm dia. (0. 12-mm x 18), 2 cores, Standard length: 2 m E3S-AD61, E3S-AD81 E3S-AD63, E3S-AD83 E3S-AD62, E3S-AD82 Receiver Lens (7 x 14) 40 17 4. 8 Optical axis Emitter (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 3 cores, Standard length: 2 m 12. 4 12 16. 9 10. 7 16. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 7. 2 41. 7 Four mounting holes 20 3. 1 3. 6 Light indicator (red) Sensitivity adjustor (white) 3. 6 7 21 29. 2 1. 3 Stability indicator (green) Mode Selector (black) Dark-ON Light-ON D L A (see note) 10. 7 A (see note) 1. 2 10. 5 20+0. 2 Two, M3 x 12 screws E3S-AD71, E3S-AD91 E3S-AD73, E3S-AD93 E3S-AD72, E3S-AD92 Note: The mounting bracket can be attached to side A. Receiver Lens (7 x 14) 17 40 4. 8 Optical axis Emitter (4) Polyvinyl chloride-covered cord, 4-mm dia. (0. 12-mm x 18), 4 cores, Standard length: 2 m 12. 4 12 16. 9 10. 7 14. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 3. 1 3. 6 7. 2 41. 7 Four mounting holes 20 Stability indicator (green) Light indicator (red) Sensitivity adjustor (white) 1. 3 Mode Selector (black) Dark-ON Light-ON 3. 6 7 21 3. 5 OFF-delay time adjustor/turbo switch (black) (see note 1) Turn to adjust the OFF-delay time: push to switch turbo function 29. 2 D L A (see note) 10. 7 A (see note) 12 10. 5 20+0. 2 Two, M3 x 12 screws Note: 1. The mounting bracket can be attached to side A. A-250 Standard Photoelectric Sensors Connector Type 40 12. 9 7 (10) 12. 4 12 16. 9 16. 5 Mounting Holes 10. 7 Two, M3 holes 3. 2 7. 2 3. 2 4. 8 Stability indicator (green) 10. 5 30 Lens (7 x 7) Optical axis 5 20 7. 2 20 Two mounting holes Mode Selector (black) Dark-ON Light-ON 1. 3 21 8 A (see note) 5. 5 16. 2 1. 2 10. 7 A (see note) 29. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AT16, E3S-AT36 (Emitter) 17. 8 Light indicator (red) 40 (10) Connector M12 12. 4 12 16. 9 10. 7 16. 5 3. 2 7. 2 Mounting Holes Two, M3 holes 3. 2 4. 8 5 10. 5 20 30 7. 2 20 Two mounting holes Lens (7 x 7) Optical axis Mode Selector (black) Dark-ON 1. 3 Light-ON 21 5. 5 16. 2 A (see note) 1. 2 10. 7 Two, M3 x 12 screws A (see note) 29. 2 8 Note: The mounting bracket can be attached to side A. E3S-A A-251 E3S-A E3S-AT16, E3S-AT36 (Receiver) Light indicator (red) Sensitivity adjustor (white) Connector M12 E3S-AR16, E3S-AR36 Light indicator (red) 42. 3 15. 2 2. 3 7 Sensitivity adjustor (white) (10) Connector M12 12. 4 12 16. 9 16. 5 10. 7 3. 2 7. 2 Mounting Holes Two, M3 holes 20 Stability indicator (green) Receiver Optical axis 1. 3 21 11. 5 9 19. 8 1. 2 Emitter A (see note) Two, M3 x 12 screws 10. 7 A (see note) 29. 2 3. 2 4. 8 5 10. 5 20 30 7. 2 Mode Selector (black) Dark-ON Light-ON Two mounting holes Lens (7 x 14) Note: The mounting bracket can be attached to side A. E3S-AD16, E3S-AD36 E3S-AD18, E3S-AD38 E3S-AD17, E3S-AD37 Light indicator (red) 12. 9 7 Connector M12 Sensitivity adjustor (white) 40 (10) 14. 2 12 16. 9 10. 7 16. 5 3. 2 7. 2 Mounting Holes Two, M3 holes Stability indicator (green) 10. 5 Receiver Lens (7 x 14) Optical axis 1. 3 21 11. 5 9 19. 7 Emitter A (see note) 1. 2 10. 7 29. 2 3. 2 4. 8 5 20 30 7. 2 20 Two mounting holes Mode Selector (black) Dark-ON Light-ON A (see note) Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. A-252 Standard Photoelectric Sensors E3S-AT66, E3S-AT86 (Receiver) Lens (7 x 7) 13. 5 Optical axis 40 8. 3 14. 9 12 19. 4 10. 7 16. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 3. 1 3. 6 41. 7 7. 2 Four mounting holes 20 Stability indicator (green) 3. 6 7 21 Light indicator (red) Sensitivity adjustor (white) 1. 3 Mode Selector (black) Dark-ON Light-ON 29. 2 A (see note) Spacer (attachment) (Attach the spacer or the plug cannot be connected. ) 1. 2 10. 7 A (see note) 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AT66, E3S-AT86 (Emitter) Lens (7 x 7) 13. 5 8. 3 Optical axis 40 Connector M12 (10) 14. 9 12 19. 4 10. 7 16. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 3. 1 3. 6 41. 7 7. 2 Four mounting holes 20 Light indicator (red) Mode Selector (black) 1. 3 Dark-ON Light-ON 8. 5 21 29. 2 A (see note) Spacer (attachment) (Attach the spacer or the plug cannot be connected. ) 1. 2 10. 7 A (see note) 10. 5 20+0. 2 Two, M3 x 12 Note: The mounting bracket can be attached to side A. E3S-A A-253 E3S-A Connector M12 (10) E3S-AR66, E3S-AR86 Receiver Lens (7 x 14) 40 17 Optical axis Emitter (10) Connector M12 12 14. 9 Use these two holes for mounting. 10. 7 7. 2 20 3. 1 3. 6 41. 7 Stability indicator (green) 3. 6 7 21 29. 2 Light indicator (red) Sensitivity adjustor (white) 7. 2 Four mounting holes 20 19. 4 16. 5 Mounting Holes Two, M3 holes Mode Selector (black) Dark-ON Light-ON A (see note) Spacer (attachment) (Attach the spacer or the plug cannot be connected. ) 1. 2 10. 7 A (see note) 1. 3 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. E3S-AD66, E3S-AD86 E3S-AD68, E3S-AD88 E3S-AD67, E3S-AD87 Receiver Lens (7 x 14) 40 17 Optical axis Emitter (10) Connector M12 14. 9 12 19. 4 10. 7 16. 5 7. 2 Use these two holes for mounting. Mounting Holes Two, M3 holes 20 3. 1 3. 6 41. 7 7. 2 Four mounting holes 20 Stability indica tor (green) Light indicator (red) Sensitivity adjustor (white) Mode Selector (black) 1. 3 Dark-ON Light-ON 3. 6 7 21 29. 2 A (see note) 1. 2 10. 7 A (see note) Spacer (attachment) (Attach the spacer or the plug cannot be connected. ) 10. 5 20+0. 2 Two, M3 x 12 screws Note: The mounting bracket can be attached to side A. A-254 Standard Photoelectric Sensors Accessories Plug (for E3S-A Connector type) E3S-A Straight Type XS2F-D421-DC0-A The XS2F-D421 Straight Cable Connector is also available. [. . . ] Insert the 0. 5- or 1-mm slit between the metal cover and rubber attachment if a slit width of 0. 5 or 1 mm is desired. These slits fit into the rubber attachment. 2 mm Receiver Metal cover Slit (0. 5 mm or 1 mm) Be aware of the direction of polarization. Rubber attachment Arrow indicating position of optical axis The arrow printed on the cover indicates the direction of polarization. By attaching the filters opposite to each other in polarization to the emitters and the receivers (refer to the figure) in rows, mutual interference can be prevented (in any case, the filter attached to an emitter and to the corresponding receiver must be the same in direction of polarization or the photoelectric sensor will not function). Indented portions E3S-A Mounting Bracket The direction of the optical axis coincides with the mounting direction of the E3S when the mounting screw is inserted into the lock hole of the mounting bracket. [. . . ]