User manual OMRON CX-DESIGNER INTRODUCTION GUIDE

[. . . ] General Precautions The user must operate each product according to the performance specifications described in the operation manuals. Before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems, machines and equipment that may have a serious influence on lives and property if used improperly, consult your OMRON representative. Make sure that the ratings and performance characteristic of the product are sufficient for the systems, machines, and equipment, and be sure to provide the systems, machines, and equipment with double safety mechanisms. This manual provides information for using the programmable terminal model NS12. [. . . ] "2" Set as follow from the address setting menu. Host Name ![1] Click Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Click Create two labels as shown on the right by referring to "9. Uncheck the box. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Double-click the frame object. Check the "Do not show this dialog again" box. Click Create a bit lamp by referring to "12. Enter the following settings for [Display Address 1] in the property list. Host !Double-line Circle Set [Color 1] and [Color 2]. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create six bit lamps by referring to "11. "6" Repeat direction Set "1" to [Offset Address] Click Create a label "Alarm1" by referring to "9. Uncheck the box. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Copy a label object by dropping & dragging the label "Alarm 1" while holding down the [Ctrl] key. With three labels selected, select as follow: [Edit] menu -[Align/Distribution] -[Distribute Vertically] With three labels selected, select as follow: [Edit] menu -[Align/Distribution] -[Align Left] Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create labels "Alarm 4 to 6" in the way you created "Alarms 1 to 3". Left-click The next page of the Frame object (page 1) is displayed. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create a bit lamp by referring to "12. Double-lined Circle Select [Color 1] and [Color 2] Create6 bit lamps by referring to "11. "6" Repeat direction Set "1" to [Offset Address] Click Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create a label as shown on the right by referring to "9. Uncheck it. Create labels for "Alarms 8 to 12" in the way you created "Alarms 1 to 6". Click any area on the screen except frame objects to finish "Edit Inside Group/Frame. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project 15. Numeral Display & Input Numeral Display & Input is an object that displays data of an address as numeral value and changes data by inputting numeral value from a virtual key board. Touch the object on the screen. The user can enter values The user can enter values to the specified area. to the specified area. Create labels as shown on the right by referring to "9. "Set Value". Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Select the Numeral Display& Input icon and place it next to the label "Present Value". "0" Select the Numeral Display & Input icon from the object list Set as follow from the object property list. "White" Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project 16. Word button is an object that writes constants to the address (DM etc. . . ) when it is pressed, or increases/decreases the value of the address. It is possible to display a pop-up menu and select the value from constants. In this manual, you will create a word button to write the set value (Internal address) to the present value (PLC address). Paste a Word button. Set as follow on the object property list. General tab [Address] !"$W0" Also set [Color 1] and [Color 3]. Text tab [Label] !"Transfer" Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create three labels by referring to "9. [. . . ] In this manual, you will select ON/OFF buttons. Right-click the screen to display the pull-down menu. Click [Select Object]. Click [ON/OFF Button]. The ON/OFF Buttons are displayed . Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project 23-4 Reuse of screen (by copying) 23-4 Reuse of screen (by copying) "Reuse of Screen" is a function to use an already-made screen and copy them to another project. In this manual, you will reuse Screen Page 1 made in the sample project (GUIDE) to another project (GUIDE 2). Right-click [0000: Screen Page 1] on the Project Workspace to display the pull-down menu. Click [Copy]. Start-up another CXDesigner and create a project "GUIDE 2" by referring to"3. Do not close the CXDesigner on which you have been editing the project "GUIDE". [. . . ]