User manual OLIVETTI D-COPIA 42

[. . . ] Direzione Home/Office Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivettilexikon. com Copyright © 2001, Olivetti All rights reserved February 2001 The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. The mark affixed to the product certifies that the product satisfies the basic quality requirements. The auto-shut-off time setting is between 15 and 120 minutes in the areas corresponding to the Swiss Energy 2000 Program area. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · · · incorrect electrical power supply; incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. <Attention> This instruction handbook is for the d-Copia 42 (42 ppm) and d-Copia 52 (52 ppm). Specific matters for 52 ppm copier are covered on page 99 and thereafter. [. . . ] Automatic turning OFF of the copier reduces unnecessary power consumption in the standby mode and at night where the copier is left on, resulting in reduction in power rate. * For the change of time until the auto shut off function, see the "8 AUTO SHUT-OFF TIME" on page 79, and to cancel the auto shut-off function, see the "0 AUTO SHUTOFF" on page 80. * If the auto shut-off function operates when the week timer (page 67) is set or an optional I/F kit is equipped, the machine will be in the rest state leaving the main switch ON ( | ). Press the energy saver key to perform copying. 48 APPLICABLE COPY MODES (1) Reserving another copy while copying is performed [Add Job] While copying is performed, another copying can be reserved. * When this copy mode is used, the optional memory copy board is required. q Introduction of the add job screen 1 Job number key: The serial number is assigned until 99 in the order of registration. Even when the order is altered and the job is cleared, no number is changed. Copying operation is carried out from the job displayed in the upper part. 5 Residual memory: The data volume of originals stored in memory is displayed. * The form overlay mode cannot be used in the add job function. 1 Add job 1. If the message "ADDITION OF JOB IS POSSIBLE. " is displayed, the job can be reserved. * To stop job reservation, touch the "END" or "BACK" key. 2. Referring to page 19 and subsequent pages, set the function to be reserved and press the Start key. After all the original has been read, the touch panel will return to the step 2 screen. Copying will begin in the order of reservation when the copying of previously reserved job is completed. 49 APPLICABLE COPY MODES 2 Changing the setting contents of the add job The setting of finishing for the reserved job (number of copies and sorter mode) can be changed. When changing the number of copies, touch the "+" key or "-" key for setting. * Change the setting of finishing. * If an optional finisher has been installed, the staple sort mode and the punch mode can be adjusted. When using the booklet stitcher, the staple sort mode can be adjusted. 5. After all the settings has been completed, touch the "END" key. The touch panel will return to the basic screen. 50 APPLICABLE COPY MODES 3 Clearing the add job 1. The touch panel will return to the basic screen. 4 Changing the add job order Although job will be copied in the order of reservation, the order can be changed after the reservation. Change the order by touching the "v UP" key or "w DOWN" key. * Copying operation is carried out from job displayed upper side to lower. 51 APPLICABLE COPY MODES 4. [. . . ] Remove all misfed originals in accordance with page 93. ) & Original insertion guide (Set to match the size of the original when setting in the DF. ) * Original table (Set the DF original on this table. ) ( DF opening/closing lever (Hold when opening and closing the DF. ) ) Original ejection cover (The copied originals are stored here. ) 99 ABOUT 52 PPM COPIER / Paper ejection guide (Open when setting an original of B4 or larger in the DF. ) ¤ Main switch (Turn ON ( | ) before starting machine. ) < Left cover (Open when paper misfeed occurs in the fixing unit or ejection section. ) > Copy tray (Completed copies will be ejected here. ) fi Toner cartridge fl Toner cartridge release lever (Operate when replace a toner cartridge. ) Paper transfer section release button ° Paper transfer section handle · Paper transfer section release lever (Operate when paper misfeed occurs in the paper transfer section. ) , Paper feed section knob (Operate to remove paper misfed in paper feed section. ) OE Duplex unit , , Re-feeding section (Open when paper misfeed occurs in the duplex unit. ) ´ Duplex cover (Open when paper misfeed occurs in the duplex unit. ) Duplex unit handle (Operate to pull out duplex unit. ) Fixing unit Á Fixing unit handle (Pull out the fixing unit to remove paper misfed in fixing unit by handling this. ) ¨ Fixing knob (Operate to remove paper misfed in fixing unit. ) ^ Fixing unit release lever (Operate to open/close fixing unit. ) Ø Handles for transport (Pull out to be handle. They are located in four positions. ) 100 ABOUT 52 PPM COPIER q Management code The management code registered in the management mode described in the second paragraph on page 62, the first paragraph on page 68, the third paragraph on page 72 and the second paragraph on page 77 is 5200. See "9 CHANGE MANAGEMENT CODE WITH #-KEYS" on page 79. q Auto shut-off time The initial setting for "8 AUTO SHUT-OFF TIME" described on page 76 is 90 minutes. For the details, see the setting procedure on page 79. q Opening/closing the front cover The shape of the front cover is different on 52 ppm copier, therefore how to open and close the front cover is different. [. . . ]