User manual OLIVETTI D-COPIA 3501

[. . . ] d-Copia 3501 / 3501MF d-Copia 4501 / 4501MF Operation Manual Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product. Before installing this product, be sure to read the installation requirements and cautions sections. Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual (for general information and copier operation)" and operation manuals for any optional equipment which has been installed. PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. [. . . ] About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen. 2 Select the shift direction. Touch a shift direction key to select right or left. The selected key will be highlighted. RIGHT LEFT 5-3 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase width is approximately 10 mm (1/2") in it's initial setting. NOTE The initial setting for the erasure width can be changed in the key operator programs to any value from 0 to 20 mm (0 to 1"). (Page 15 of the Key operator's guide) Original Copy EDGE ERASE Eliminates shadow lines around the edges of copies caused when heavy paper or a book is used as an original. CENTRE ERASE Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTRE ERASE Eliminates shadow lines around the edges of copies and eliminates the shadow at the centre of copies. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Adjust the amount of erase and touch the [OK] key. CANCEL EDGE OK 1 MODES Touch the [ERASE] key on the special modes screen. DUAL C TAN C 10 (0 mm 20) RGIN SHIFT ERASE PHLET COPY JOB BUILD The erase setting screen will appear. The erase icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. Use the and keys to set the erase width to any value from 0 to 10 mm in 1 mm increments (0" to 1" in increments of 1/8"). 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. NOTE When erase is used, edge erase takes place at the edges of the original image. If you also use a ratio setting, the edge erase width will change according to the set ratio. To cancel the erase function, touch the [CANCEL] key on the erase setting screen (step3). 2 Select the desired erase mode. ERASE EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE Select one of the three erase modes. The selected key will be highlighted. 5-4 SPECIAL MODES Dual page copy The dual page copy function produces separate copies of two documents placed side by side on the document glass. This function is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book Book original Dual page copy The dual page copy function can be used only when copying from the document glass. Only A4 (8-1/2" x 11") paper can be used. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 4 Ensure that 8-1/2" x 11" (A4) size paper is selected. AUTO EXPOSURE AUTO A4 PAPER SELECT 100% COPY RATIO If A4 (8-1/2" x 11") size paper is not selected, touch the [PAPER SELECT] key to select A4 (8-1/2" x 11") size paper. 1 Touch the [DUAL PAGE COPY] key on the special modes screen. OK 1/3 RASE DUAL PAGE COPY TANDEM COPY JOB BUILD The [DUAL PAGE COPY] key will be highlighted to indicate that the function is turned on, and the dual page copy icon ( ) will appear in the upper left of the screen. 2 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow For two-sided copying, follow steps 2 through 4 on page 4-13 and then follow steps 4 through 7 on page 4-12. NOTE To erase shadows caused by document binding, use the edge erase function (page 5-4). (Centre Erase and Edge + Centre Erase cannot be used in combination. ) To cancel the dual page copy function, touch the [DUAL PAGE COPY] key on the special modes screen (screen of step 1). 5 3 Place the originals on the document glass. When copying a thick book, press down lightly on the book to flatten it against the document glass. Index A4 81/2" x 11" This page is copied first. Centre line of original A4 (81/2" x 11") A3 (11" x 17") Place the opened original on the document glass so that the first page you wish to copy is on the right and the centre of the original is aligned with the size mark. 5-5 SPECIAL MODES Pamphlet copy The pamphlet copy function is used to arrange copies in proper order for eventual centre-stapling and folding into a booklet. This function is convenient for arranging copies into an attractive booklet or pamphlet. NOTE To make pamphlet copies of a book or other bound original, use the book copy function (page 5-25). [. . . ] 2-14 Total number of originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Touch panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13, 1-14, 7-4, 7-5 Transparency film . . . . . . . 2-3, 2-4, 2-10, 2-16, 4-20, 5-22 Transparency inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5, 5-2, 5-22 Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]