User manual OLIVETTI D-COPIA 200

[. . . ] Copier Operation Manual d-Copia 16 d-Copia 200 Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. PUBLICATION ISSUED BY: Olivetti Tecnost, S. p. A. Divisione Business Prodotti Office Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivettitecnost. com Copyright © 2004, Olivetti All rights reserved March 2004 The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. The mark affixed to the product certifies that the product satisfies the basic quality requirements. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · · · incorrect electrical power supply; incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. In areas of the GEEA, the available setting for the Off Mode to engage is between 1 and 120 minutes, and the available setting for the Low Power Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes or 120 minutes. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. [. . . ] Before disabling the Auto Off function, you may want to try lengthening the amount of time before the Auto Off function engages (Off Mode Transition Time). Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. Sets the time interval prior to the automatic engagement of the Low Power mode after copy operations have been completed. Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. The Alarm can be set to sound when a key on the Operation Panel is pressed or in cases when errors occur, etc. 10 - 270 (10-second units) (*90) 6-29 F34 Auto Clear Time 6-30 F35 Low Power Mode Transition Time Off Mode Transition Time 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*15) 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*30) 6-31 F36 6-31 F37 Alarm on: Enabled (sound alarm) oFF: Disabled (no alarm)* 6-32 F38 Toner Coverage Report Prints out a report that shows the number of copies --made and the average amount of toner used (blackness ratio %) for each paper size. 6-33 6-10 Section 6 COPIER MANAGEMENT Default Settings Mode Operations Procedures Follow the procedure listed below to operate in the [Default Settings Mode]. 4 Press the [Enter] key. Inch specifications Metric specifications 1 Depress the [Exposure Adjustment] keys on both sides for 3 seconds. of Copies display. Procedure for Changing the Default Settings The procedure for changing each of the items in the Default Settings is described below. Press either the Zoom (+) key or the Zoom (­) key and select each Default Settings Mode. Inch specifications Metric specifications 2 User Status Report Outputs a list of the values set for the Default Settings items. Note Check to make sure that 11" × 8 1/2"/A4 size paper is loaded in the drawer. 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications Notes · Each of the Default Setting Modes can be selected by pressing the Keypad keys. · Refer to "Procedure for Changing the Default Settings" regarding the following. 3 After completing each operation, press on the Zoom (+) or Zoom (­) key to display "F00". Inch specifications Metric specifications 2 Press either the Zoom (+) or Zoom (­) key to display "F01". Inch specifications Metric specifications 6-11 Section 6 COPIER MANAGEMENT 3 Press the [Enter] key. Inch specifications Metric specifications 2 Press either the Zoom (+) or Zoom (­) key to display "F02". Inch specifications Metric specifications Sample: User Status Report 3 Press the [Enter] key. Inch specifications Metric specifications 4 Press either the Zoom (+) key or the Zoom (­) key and select "1- (Text + Photos)", "2- (Photos)" or "3- (Text)". Inch specifications Metric specifications 5 Original Image Quality Sets the original image quality that will be selected at the time the copier is turned on. Press the [Enter] key. Inch specifications Metric specifications 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications 6-12 Section 6 COPIER MANAGEMENT Exposure Mode Sets the copy exposure at the time the copier is turned on to Manual or Automatic. 5 Press the [Enter] key. Inch specifications Metric specifications 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications Eco-copy 2 Selects the initial value of Eco-copy when the power is turned on. [. . . ] 5-8 Making enlarged and reduced copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Margin Shift (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25 Merge Copy Borderline (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27 Mixed Original Sizes (Auto Selection) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]