User manual OLIVETTI D-COPIA 1601 E 2001

[. . . ] OPERATOR MANUAL Printed in Italy Code 539506EN GB PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2007, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by the United States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Do not make copies of anything which is prohibited from copying by law. [. . . ] (CENTRE ERASE) The factory default setting for the width of the erasure is approximately 10 mm (1/2"). (p. 41) EDGE ERASE A Original CENTRE ERASE Original · · · · A Copy Copy EDGE + CENTRE ERASE AB AB Original Copy AB AB Note Centre erase cannot be used in combination with dual page copy. (p. 31) Erase copy cannot be used when the paper is a special size or copying from the bypass tray. Note that if the width of the erasure is too large, the edge of the image may be partially erased. 1 2 Place the original(s). (p. 18) If the original is placed on the document glass, select the original size. (p. 18) When using the SPF, make sure that the same ORIGINAL SIZE indicator as your original size lights up. 4 Set the number of copies and other settings, and then press the [START] key ( ). The copy is delivered to the paper output tray. · To cancel erase copy, press the [ERASE] key ( / ) repeatedly until the ERASE indicators ( / ) are both off. · If the original size was not selected in step 2, erase copy cannot be used. Note 3 Press the [ERASE] key ( / select the desired erase mode. ) to To select the "EDGE + CENTRE ERASE" mode, press the [ERASE] key ( / ) until both the EDGE ( ) and CENTRE indicators ( ) light up. 34 4 Note Chapter 4 PRINTER FUNCTIONS The machine includes a USB 1. 1 connector and a parallel connector as standard equipment. A computer can be connected to these connectors to use the machine as a printer. When the dual function board is used, the following functions can be used in addition to the standard printer functions. · High-speed data transfer (when connected to a USB 2. 0 connector) · ROPM* function · Automatic rotation printing To use the machine as a printer, the printer driver must first be installed as explained in the "Software Setup Guide". * ROPM is an acronym for "Rip Once Print Many" processing. The ROPM function stores multiple pages of print data in memory before printing. When printing multiple copies, this eliminates the need for the computer to repeatedly transmit the print data. · If a problem occurs in printer mode, see "TROUBLESHOOTING". (p. 48) · Two printer drivers are provided for the machine: a standard printer driver and a printer driver that is used when the dual function board is installed. Install the correct printer driver depending on whether or not the dual function board is installed. If the correct printer driver is not used, printing may not take place correctly. (See the "Software Setup Guide" for information on installing the printer drivers. ) · When using USB 2. 0 (Hi-Speed mode), be sure to read "System requirements for USB 2. 0 (Hi-Speed mode)" (below) to verify that your system and the machine settings are configured appropriately. · Do not install the printer driver for the dual function board when the dual function board is not installed. If this is done, a warning message will be printed out, and the print job will be cancelled. · When interrupt copying is being performed, printing is not possible. System requirements for USB 2. 0 (Hi-Speed mode) The following system is required to use USB 2. 0 (Hi-Speed mode): · Your computer must be running Windows XP / Windows 2000 and the Microsoft USB 2. 0 driver must be pre-installed, or the USB 2. 0 driver for Windows XP / Windows 2000 must be installed using Microsoft's Windows Update service. · The "USB 2. 0 mode switching" setting in the machine's user programs must be set to "Hi-Speed". To change the setting, see "USB 2. 0 mode switching" in the user programs. [. . . ] 24 Convenient copying functions 2 IN 1 / 4 IN 1 copy - Document cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 - SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Centre erase copy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Edge erase copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]