User manual OLIVETTI D-COLOR MF35 SUPPLEMENTO

[. . . ] Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. This manual is also available in color PDF format on the CD-ROM provided. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Contents 1 Introduction Energy Star®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1. 1 1. 2 Trademarks and registered trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The touch panel is adjusted, and the Accessibility Setting screen appears again. 5 Touch [Close] or press the [Accessibility] key. The Basic screen appears again. 2 Note If the touch panel cannot be adjusted, contact the technical representative. ! Detail To cancel the touch panel adjustment, press the [Stop] key or the [Reset] key. d-Color MF35 (Phase3) 5-37 5 To set the "Auto Reset Notification" function Additional copy operations When the automatic panel reset operation is performed, a message can be displayed, requesting confirmation to reset the settings in Enlarge Display mode. In addition, it is possible to specify when the message is displayed, requesting confirmation to reset the settings in Enlarge Display mode. The factory default setting is "OFF". 1 2 Display the Accessibility Setting screen. (To display the screen, refer to page 5-26) Touch [Auto Reset Notification] or press the [6] key in the keypad. 5-38 d-Color MF35 (Phase3) Additional copy operations The Auto Reset Notification screen appears. 5 3 Touch the button for the desired display time. ­ ­ ­ To not display the message requesting confirmation to reset the settings in Enlarge Display mode, touch [OFF]. To display the message requesting confirmation to reset the settings in Enlarge Display mode, touch the button ([30 sec. ], [60 sec. ], [90 sec. ] or [120 sec. ]) for the length of time that the message is to be displayed. To cancel changes to the settings, touch [Cancel]. 4 5 Touch [OK]. The Basic screen appears again. d-Color MF35 (Phase3) 5-39 5 2 Note Additional copy operations The Enlarge Display mode is compatible with basic copy, scanning and fax functions. With the Enlarge Display mode, text and illustrations are displayed at a larger size so that they can be seen more easily. For details on the Enlarge Display mode, refer to the [Enlarge Display Operations] of the user manual. If the time setting is the same for the automatic panel reset operation and the automatic system reset operation, the display of the message requesting confirmation to cancel Enlarge Display mode is given priority and the message requesting confirmation to reset the settings in Enlarge Display mode is not displayed. 5-40 d-Color MF35 (Phase3) Additional copy operations To set the "Enlarge Display Confirmation Screen" function 5 When the [Enlarge Display] key is pressed to change the display of the screen, a message can be displayed, requesting confirmation to reset the settings to their defaults. The factory default setting is "No". 1 2 Display the Accessibility Setting screen. (To display the screen, refer to page 5-26) Touch [Enlarge Display Confirmation Screen] or press the [7] key in the keypad. The Enlarge Display Confirmation Screen screen appears. d-Color MF35 (Phase3) 5-41 5 3 Additional copy operations Select whether or not the message is displayed. ­ To cancel changes to the settings, touch [Cancel]. 4 5 Touch [OK]. The Basic screen appears again. 2 Note The Enlarge Display mode is compatible with basic copy, scanning and fax functions. With the Enlarge Display mode, text and illustrations are displayed at a larger size so that they can be seen more easily. For details on the Enlarge Display mode, refer to the [Enlarge Display Operations] of the user manual. If [No] is touched in the message requesting confirmation to enter Enlarge Display mode, the screens are not changed. 5-42 d-Color MF35 (Phase3) 6 Troubleshooting Troubleshooting 6 6 6. 1 Troubleshooting When the message "Malfunction detected. " appears (call technical representative) If a malfunction that cannot be corrected by the user occurred, the message "Malfunction detected. (call technical representative screen) The phone number and fax number for the usual technical representative appears in the center of the call technical representative screen. Display in Enlarge Display mode If a malfunction occurs, the screen shown below appears. d-Color MF35 (Phase3) 6-3 6 Touch Troubleshooting to display the message shown in the following illustration. 6-4 d-Color MF35 (Phase3) Troubleshooting To call the technical representative 6 1 2 Write down the malfunction code (for example, C-0001) in the call technical representative screen. Press the sub power switch to turn off the control panel. 3 Use the main power switch to turn off the machine. 4 5 Unplug the machine. Contact the technical representative, and inform them of the malfunction code. 2 Reminder Since the machine may be damaged, contact the technical representative according to the procedure described above as soon as the call technical representative screen appears. d-Color MF35 (Phase3) 6-5 6 6. 2 Troubleshooting When the message "Misfeed detected. " appears If a misfeed occurs during copying or printing, the message "Misfeed detected. " appears and the location of the misfeed is indicated in the screen. (misfeed screen) At this time, copying and printing cannot continue until the misfeed is adequately cleared. Location of paper misfeed A flashing "o" indicates the location of the paper misfeed. [. . . ] Insert Sheet Set this function to insert paper from the specified paper tray into the copies as chapter title pages. M Margin Select the setting for the position of the binding margin for the loaded original. Selecting the appropriate setting prevents the copy from being printed upside-down when making double-sided copies from single-sided original or when making single-sided copies from double-sided originals. Memory Scan Scans an original exceeding the maximum 100 pages that can be loaded into the ADF by scanning the original in separate batches. In addition, the scanning location can be switched between the original glass and the ADF during the scanning operation. [. . . ]