User manual OLIVETTI ARTJET 20 BROCHURE

[. . . ] Connect the other end of the interface cable to the appropriate interface connector socket (port) on your computer/host system. u to the electrical power supply 1. 2. Insert the small two-pin connector of the printer power cable in the socket on the rear the printer. Plug the other end of the cable into an independent wall socket. The socket outlet shall be near the printer and shall be easily accessible. Make sure that the plug on the power cable of the printer is of the type accepted by the wall socket you intend to use. Do NOT attempt to change the plug yourself. 4 Installation guide english. chp Tue Feb 02 10:03:46 1999 Color profile: Disabled Composite Default screen 1. Push up the output tray, to simplify access to the main automatic feeder. 2. Pull out the adjustable rear guide on the paper tray of the main feeder and make sure that the adjustable margin guides are completely open. 3. Fan the paper and load it as a single pack into the main feeder, inserting it carefully until it stops inside the printer. Do NOT load paper above the maximum level indicated on the inside of the feeder. 4. The printing surface must face towards the tray. [. . . ] Click the button, to print the so that you can check that the print quality is satisfactory; follow the instructions displayed. (This feature requires one sheet of paper). Printer Care Head Align accuracy of bi-directional printing; Demo demo page Once you have done these operations, you can reduce the Printer Monitor to its icon. Your printer is now ready for use. Installation guide 7 english. chp Tue Feb 02 10:03:51 1999 English Install the printer software Complete printer installation Color profile: Disabled Composite Default screen Operator panel Power Paper u Light indicator Status Condition off Printer not powered. Vertical operating position lit Printer powered. flashing slowly Printer is receiving data. flashing rapidly Operating error. Horizontal operating position Paper Power flashing very rapidly Failure condition. flashing with specific variable sequence Print head initialisation cycle or service function u Buttons - basic functions Function Button Description Printer on/off Power Toggles the printer ON/OFF condition. Paper control Paper 1) If paper is already present in th e p rin te r, causes its expulsion. 2) Loads a sheet of paper in t h e p r in t e r ONLY a f t e r a paper error signal. Once you have corrected the error condition (paper out, paper jam), press to load a document and continue your print job. For a description of the special functions that you can activate using the buttons on the operator panel, see the On Line documentation loaded when you installed the printer driver. 8 Installation guide english. chp Tue Feb 02 10:03:52 1999 Color profile: Disabled Composite Default screen u General care · · · · · · · Place you printer in a clean, stabilised environment. Dont leave it exposed to direct sunlight or heat sources, or in dusty, dirty or poorly-ventilated environments. Temperature: 60 to 95 F - 15 to 35 C Relative Humidity: 20% - 80% Connect your printer to an independent power socket. If your printer does not work, DO NOT ATTEMPT TO REPAIR IT YOURSELF. Recommended Operating Environment o o Make sure the paper feeds smoothly, and that it is not held too tightly nor has too much play. · Printing on both sides of the paper may increase the risk of misfeeds or paper jams and may cause smudging. · If you remove the paper from or add paper to the main feeder, you repeat the entire paper loading operation. · When using user-defined/non-standard size formats, remember to select the appropriate paper type in your printer driver (see the loaded with your printer driver). · MUST On-Line Documentation u Print heads Remove the print heads from the printer only to replace them. · Always keep the new print heads sealed in their containers until they are to be used. · · Remember to remove the protective tape · · · u Paper · Use manufacturer-recommended paper and printing media. For all types of special printing media, always read the instructions included with the media pack. The paper/printing media must not be damp, curled, crumpled or torn, otherwise it may jam or even not be inserted. Always use paper/printing media in perfect condition and within the specifications defined (see Product Characteristics). · When loading paper/printing media, make sure the printing surface of the paper is facing the correct way. [. . . ] There are several ways of accessing information on the printer settings in the Settings tab (Start, select and click · select the item required and then right click it or · select ?in the top right hand corner of the tab and drag it on to the item required. [. . . ]