User manual OKI PRO510DW

[. . . ] All Rights Reserved Document Information ________________________________ pro510DW User's Guide P/N 59321501 Revision 1. 0 March, 2010 Disclaimer__________________________________________ Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . [. . . ] The printer may not work if a USB- compatible device is connected concurrently with other USB-compatible machines. When connecting multiple printers of the same type, they appear as *****, ***** (2), ***** (3), etc. These numbers depend on the order of connecting or turning on each printer. > Ethernet ­ For network cable connection. NOTE Interface cables are not supplied with your printer. User's Guide> 44 CONNECTING THE PARALLEL INTERFACE 1. Connect a parallel cable between the printer and computer. 3. Turn on the printer and then the computer. CONNECTING THE USB INTERFACE Do not connect the USB cable at this time. You will be instructed when to connect the USB cable when you run the Drivers CD. If you are connecting your printer directly to a stand alone computer proceed to the section entitled "Printer Drivers". User's Guide> 45 CONNECTING THE NETWORK INTERFACE CAUTION! Do not connect a USB cable into the network interface connector as this may lead to malfunction. Install the Ferrite core to the Ethernet cable as shown. User's Guide> 46 3. Connect an Ethernet cable between the printer and an Ethernet hub. 4. Turn on the printer and then the computer. If your printer is to be installed as a network printer, please refer to the relevant section in the Software Installation Guide and Configuration Guide for further details on how to configure the network connection before installing the printer drivers. NOTE Administrator's authority is required when installing a network connection. USING THE DRIVERS CD Insert the Printer Software CD into your computer and follow the onscreen instructions. You are prompted to follow a set of basic steps to configure the display panel language, install drivers and other software and finally print a test page to check that your printer is operating correctly. User's Guide> 47 OPERATION USING THE PRINTER For full details of how to use the printer and any accessories to print jobs efficiently and effectively, please refer to the Printing Guide. User's Guide> 48 CONSUMABLES AND MAINTENANCE This section explains how to replace consumable and maintenance items when due. As a guide, the life expectancy of these items is: > Black Toner -- 18, 500 Letter pages at 5% coverage. > Cyan, Magenta, Yellow Toner-- 16, 500 Letter pages at 5% coverage The printer is shipped with sufficient toner for 7, 500 Letter pages in the print cartridges of which 1 ­ 2, 000 Letter pages of toner are used to charge the image drum. > Image drum -- 42, 000 Letter pages average life > Transfer belt -- Approximately 100, 000 Letter pages > Fuser -- Approximately 100, 000 Letter pages > Waste toner -- 30, 000 Letter pages average life CHECKING CONSUMABLE/MAINTENANCE ITEM USAGE At any time, you can check how much of each consumable/ maintenance item is left by using the appropriate menus. For example, enter the menu system and follow the path: Configuration>Supplies Life>Cyan Toner The percentage of Cyan Toner remaining is displayed on the display panel and the printer then returns to the ready to print status. REPLACEMENT INDICATIONS The display panel provides messages to the effect that consumables/maintenance items are running low or nearing end of life followed some time later by a message that replacement is required. You should replace the item as soon as possible after this message is displayed to avoid the possibility of print quality being compromised. The paper feed rollers and the tray feed rollers do not have any replacement warning messages. Recommended replacement: after approximately 120, 000 sheets. User's Guide> 49 CONSUMABLE ITEM ORDER INFORMATION ITEM Toner, Black Toner, Cyan Toner, Magenta Toner, Yellow Image drum, Black Image drum, Cyan Image drum, Magenta Image drum, Yellow LIFE 18, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 42, 000 Letter pages avg 42, 000 Letter pages avg 42, 000 Letter pages avg 42, 000 Letter pages avg ORDER NUMBER 52124004 52124003 52124002 52124001 56124004 56124003 56124002 56124001 MAINTENANCE ITEM ORDER DETAILS ITEM Fuser unit LIFE 100, 000 Letter pages ORDER NUMBER 120V:42931701 230V: 42931702 Belt unit Waste toner bottle 100, 000 Letter pages 30, 000 Letter pages avg 42931601 42869401 User's Guide> 50 REPLACING CONSUMABLES/MAINTENANCE ITEMS Each consumable or maintenance item comes complete with its own installation details which give full instructions on replacement. You are advised to follow these instructions carefully. CAUTION! Only use genuine Oki Original consumables to ensure the best quality and performance from your hardware. Non-Oki Original products may damage your printer's performance and invalidate your warranty. All trademarks acknowledged. CLEANING THE LED HEADS You are advised to clean the LED heads: > any time you replace a toner cartridge (a LED lens cleaner is enclosed with each replacement toner cartridge) > if printing is showing signs of faded images, white stripes or blurred letters You can use a LED lens cleaner or dry, soft cloth for cleaning the LED heads. Open the top cover. User's Guide> 51 2. With an LED lens cleaner or soft cloth, gently wipe each of the four heads (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 1 2 3. Close the top cover. User's Guide> 52 CLEANING THE PAPER FEED ROLLERS Clean the paper feed rollers if paper jams frequently occur. [. . . ] Adjusts the position of the whole printing image (0. 25 mm, 0. 01 in interval) parallel to the direction of paper movement (i. e. vertically). Jam Recovery ON OFF Error Report ON OFF Print Position Adjust X Adjust Y Adjust 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01 in User's Guide> 96 ITEM Print Position Adjust VALUE Duplex X Adjust 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01in DESCRIPTION During the flip-side printing of duplex printing, adjusts the location of the whole printing image (0. 25 mm, 0. 01in interval) perpendicular to the direction of paper movement (i. e. During the flip-side printing of duplex printing, adjusts the location of the whole printing image (0. 25 mm, 0. 01 in interval) parallel to the direction of paper movement (i. e. Used for fine black adjustment for a significantly white horizontal dotted line, a significantly faded image or other such problem that occurs in results printed on plain paper. [. . . ]