User manual OKI OKIPOS 409

[. . . ] Line Thermal Printer STAR Line Mode Command Specifications Rev 0. 01 Table of Contents 1. INTERFACE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1-1) RS-232C Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1-1-1) Specifications (Conforming to RS-232). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] d2 dn+2 d2n+2 d3n+2 d4n+2 d5n+2 d6n+2 d7n+2 d8n+2 d9n+2 d10n+2 d11n+2 d12n+2 d13n+2 d14n+2 d15n+2 d16n+2 d17n+2 d18n+2 d19n+2 d20n+2 d21n+2 d22n+2 d23n+2 bit7 bit6 bit5 ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· ······· bit4 bit3 bit2 dn d2n d3n d4n d5n d6n d7n d8n d9n d10n d11n d12n d13n d14n d15n d16n d17n d18n d19n d20n d21n d22n d23n d24n bit1 bit0 d1 dn+1 d2n+1 d3n+1 d4n+1 d5n+1 d6n+1 d7n+1 d8n+1 d9n+1 d10n+1 d11n+1 d12n+1 d13n+1 d14n+1 d15n+1 d16n+1 d17n+1 d18n+1 d19n+1 d20n+1 d21n+1 d22n+1 d23n+1 STAR Line Mode Command Specifications 3-34 ESC X n1 n2 d1. . . dk [Name] [Code] Fine density bit image (Compatible with 24 bit wire dots) ASCII ESC X n1 n2 d1 . . . dk 1 (n1 + n2 x 256) printable region k = {(n1 + n2 x 256) x 3} 0d255 [Initial Value] --[Function] Prints input bit images with 8 dots/mm resolution for both horizontal and vertical. · When {(n1 + n2 x 256) x 3} exceeds the printable region, data after d1 is handled as normal data. · When {(n1 + n2 x 256) x 3} exceeds the printable region that is currently set, only the data in the printing region is printed. · If the current position already exceeds the print region, this command discards all data. [Defined Area] STAR Line Mode Command Specifications 3-35 3-3-9) Logo ESC FS q n [Name] [Code] [x11 x12 y11 Register logo ASCII ESC FS q n Hex. 1B 1C 71 n Decimal 27 28 113 n y12 d1. . . dk]1. . . [xn1 xn2 yn1 yn2 d1. . . dk]n [x11 x12 y11 y12 [x11 x12 y11 y12 [x11 x12 y11 y12 d1 d1 d1 . . . dk]n [Defined Area] [Initial Value] [Function] 1n255 0xn1255, 0xn23 1(xn1 + xn2 x 256)1023 0yn1255, 0yn21 1(yn1 + yn2 x 256)288 0d255 k = {(xn1 + xn2 x 256) x (yn1 + yn2 x 256) x 8} --Parameter details · n: Specifies registered logo count · xn1, xn2: Horizontal size of registered logo {(xn1 + xn2 x 256) x 8} dots · yn1, yn2: Vertical size of registered logo {(yn1 + yn2 x 256) x 8} dots · d: Registered logo data · k: Logo data count This command should be specified at the top of the line. When the first parameter is determined to be free of error, the printer starts processing this command. When logo register processing starts, all previously defined data is deleted. (It is not possible to reregister a portion of a plurality of defined logo data. ) Logo registration numbers are defined in rising order from 1. If the defined area specified by the parameter is not empty, or if there is an error in the parameter specification, register processing is aborted. (The pre-registered and complete data is effective. ) The printer should be initialized if logo registration is completed or register processing is aborted. If an error occurs while performing register processing (the time from when the first parameter is OK until th printer initialization is completed after registering a logo), error processing, mechanical operation and status processing cannot be performed. The relationships between input data and the actual print are shown on the next page. STAR Line Mode Command Specifications 3-36 Relationships of logo xn = xn1 + xn2 x 256, yn = yn1 + yn2 x 256 and registered data {(xn1 + xn2 x 256) x 8} dots Data MSB d[11] d[21] d[n1] (yn1 + yn2 x 256) bytes (yn1 + yn2 x 256) x 8 dots d[12] d[22] d[n2] LSB d[x1] d[x2] d[xn] STAR Line Mode Command Specifications 3-37 ESC FS p n m [Name] [Code] Print logo ASCII Hex. Decimal ESC 1B 27 FS p 1C 70 28 112 n n n m m m [Defined Area] [Initial Value] [Function] m 0, 48 1, 49 2, 50 3, 51 1n255 0m3 48m51 ("0"m"3") --Prints the logo of registration number n registered using the logo registration command (ESC FS q) according to the print mode m. Logo print mode Normal mode Double wide mode Double high mode Double high/wide mode If there is unprinted data in the line buffer, this command is executed after printing that data. Therefore, it is not possible to print with other data in the same line (characters, bit images, bar codes). If the logo horizontal print size exceeds the horizontal print region, the portion exceeding the area is not printed. · Left margin (ESC I n) · Right margin (ESC Q n) · Position alignment (ESC GS a n) · Absolut position movement (ESC GS R n1 n2) · Upside-down printing (SI) STAR Line Mode Command Specifications 3-38 3-3-10) Bar code ESC b n1 n2 n3 n4 d1. . . dk RS [Name] [Code] ASCII Hex. Decimal ESC 1B 27 b 62 98 n1 n1 n1 n2 n2 n2 n3 n3 n3 n4 n4 n4 d1 d1 d1 . . . dk dk dk RS 1E 30 [Defined Area] [Initial Value] [Function] 0n18, 48n156 ("0 n1"8") 1n24, 49vn252 ("1"n2"4") 1n4255 n3 (bar code mode), d (bar code data), k (bar code data count) definitions differ according to the type of bar code. [. . . ] Models not provided with a presenter should send this status fixed at 0. · This status is made valid and invalid using the memory switch only on models provided with a presenter. When valid, the presenter paper position status is updated, but when invalide, the presenter paper position status is fixed at 0 and there is no change in status. · Details of the Presenter Paper Position bit 3 bit 2 bit 1 Presenter Paper Position 0 0 0 Paper position 0 State where there is no paper in presenter 0 0 1 Paper position 1 State where paper is supplied (loop state) 0 1 0 Paper position 2 (Reserved) 0 1 1 Paper position 3 State where paper is discharged (Can be pulled out) 1 0 0 Paper position 4 (Reserved) 1 0 1 Paper position 5 (Reserved) 1 1 0 Paper position 6 State where paper is recovered 1 1 1 Paper position 7 State where paper is pulled out. [. . . ]