User manual OKI OKIPAGE 18 NETWORK CARD

[. . . ] OkiLAN 6100e+® User's Guide High Performance Ethernet Network Print Server Copyright and Trademark Information Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in products made by other manufacturers and referred to in this handbook will not affect the applicability of the information in it. T. M. , M. D. , . , and OKICOLOR T. M. , OKI Electric Industry Co. , Ltd. ; Windows, MS-DOS Reg. [. . . ] Performing this operation will restore parameters for the TCP/IP protocol to factory defaults. If you reset the OkiLAN 6100e+ while a job is printing, the job may not print successfully. OKI OkiLAN 6100e+ User's Guide IV - 47 TCP/IP Section 4 - Appendix A - Troubleshooting Appendix A Troubleshooting Main Status Indicator Upon power-up, the main status indicator flashes orange. If the indicator turns solid orange due to an error, a configuration sheet will be printed automatically. Check the error message reported on the configuration sheet. Restoring the OkiLAN 6100e+ to Factory Defaults In most cases, the best way to restore the OkiLAN 6100e+ to factory defaults is via telnet. However, if you are unable to connect to the device because of a configuration error, use the following method which does not require a network connection. To restore the OkiLAN 6100e+ to factory defaults, complete the following steps: 1. While holding in the Print Configuration Sheet Test button, power up the OkiLAN 6100e+. It will have restored itself to defaults. IV - 48 OKI OkiLAN 6100e+ User's Guide Section 4 - Appendix A - Troubleshooting Unable to Assign IP Address Gleaning If you ping the device and are not getting a response, the glean is not working. Check the following possible problems: · Verify the ARP table contains the correct hardware and IP address by running the `arp -a' command. · If you are getting a response, but the OkiLAN 6100e+ LED is still blinking green, power down the print server and try the ping again. · Verify the OkiLAN 6100e+ is on the same subnet as the computer running the ping. · The glean will not work if the OkiLAN 6100e+ has already defaulted to an IP address two minutes after power up. The LED will turn solid green and the device will print a configuration page. Power cycle the device and try the glean again. RARP or BOOTP If you are using a BOOTP or RARP server and the OkiLAN 6100e+ is not getting an IP address, check the following: · Verify the BOOTP/RARP configuration files are correctly set up ("/etc/ethers" and "/etc/hosts" for RARP and "/etc/bootptab" for BOOTP). Verify the files have the correct hardware address of the OkiLAN 6100e+. If using RARP, check that the hostnames are the same between the "/etc/ethers" and "/etc/hosts" files. OKI OkiLAN 6100e+ User's Guide IV - 49 TCP/IP Section 4 - Appendix A - Troubleshooting UNIX BOOTP If you are running UNIX, try the following methods with the BOOTP server (check the documentation for your particular UNIX flavor). · Verify the BOOTP server has reread the "/etc/ bootptab" file when the new entry was added. If the BOOTP server was running when you added the new entries, the server might not have reread the new bootptab file. For example, kill -HUP <process id of bootpd> tells it to reread "/etc/bootptab". If this does not work, restart the BOOTP server (kill and restart the process). · Some BOOTP servers will write their internal bootptab tables to a file when they receive a SIGUSR1 signal. You can check this file to verify the hardware and IP address are correct. [. . . ] · Increase the distance between the equipment and the receiver. · Consult your dealer or an experienced radio/TV technician for additional advice. OKI is not responsible for radio/TV interference caused b using unauthorized cables or by making unauthorized changes to this equipment. IX - 2 OKI OkiLAN 6100e+ User's Guide Section X: IR Printing IR Printing Section X - IR Printing In This Section Chapter 1: IR Tranceiver Features . . . . . . . . . . . . . . . . . . . . . . . . X-5 General Information on Configuring Your Print Server for IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]