User manual OKI OKIPAGE 10EX ACCESSORY INSTRUCTION GUIDE

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki Data. Please address any comments to: Training and Publications Department Oki Data Americas, Inc. [. . . ] 19 Hardware Installation Guide: English | 3 Introduction Overview With the OKIPAGE Flash SIMM (Single In-line Memory Module) card installed in your printer, you can store information such as downloaded fonts, bar codes, form overlays and macros. These are stored in "flash" memory, which means that they are not erased when the printer is switched off. Use the OKI Image Creator and NetFlash software utilities on the CD included in this kit, to download flash memory fonts and macros, etc. ! Your OKIPAGE printer accommodates only one Flash SIMM. Be sure to insert the SIMM into the socket specified in the following sections. Kit contents Kit # 70035701 · 4 MB Flash SIMM card · CD · SIMM Installation Guide Kit # 70035801 · 8 MB Flash SIMM card · CD · SIMM Installation Guide ! Fonts, forms or bar code images are not provided with this kit. Follow the instructions in this guide to install the Flash SIMM in your OKIPAGE printers and install the Image Creator and NetFlash utilities in your computer. Operating instructions for the Image Creator and NetFlash utilities are located on the CD included in this kit. 4 | OKI Flash SIMM Installing Flash Overview Memory in the OKIPAGE® 10i, 10i/n, 10e, 10ex, 12i and 12i/n Printers For models listed above, the flash memory SIMM is installed on one of the following optional accessory boards. · 1 MB Memory Expansion Kit (Part # 70033101) · RS-232C Serial Interface Kit (Part # 00025302) · OKILAN® 310e Network Interface Kit (OKIPAGE 10i only) (Part # 70032901) · OKILAN® 310e+ Network Interface Kit (OKIPAGE 12i only) (Part # 70032902) If your printer is not equipped with one of these accessories, you will need to purchase the accessory to install the Flash SIMM in the printer. Expansion sockets are provided on each board included in the option kits. Preparing Your Printer !SIMMs and circuit boards can be damaged by static electricity and rough handling. Keep the SIMM card and option board in the packaging until you're ready to perform the installation. To avoid damage to the SIMM card, ground yourself by touching the chassis of your computer each time before handling. Disconnect printer from power before beginning installation procedure. 1 Turn the printer off and unplug the power cord. 3 If an option board is already installed in your printer, turn the screws counterclockwise, then slide the board out of the printer. Hardware Installation Guide: English | 5 Removing the Access Plate If you are installing an option board for the first time: a. access plate Installing the SIMM Card Install the Flash SIMM card in the SIMM 2 socket on the option board. Use a screwdriver to pry the plate from the back panel of the printer. bottom 2 Remove the SIMM card from its packaging. [. . . ] 3 Push the OPEN button, then open the top cover. 14 | OKI Flash SIMM 5 Pull the side panel out and remove it from the printer, then close the cover to protect the image drum from light while you are installing the SIMM. 6 Remove and save the screws on the metal plate covering the internal board, then lift the plate out. Hardware Installation Guide: English | 15 Installing the SIMMs 1 Locate the SIMM sockets on the board. The top socket (1) is used for a Flash SIMM. 2 Hold the SIMM with the metallic contact edge (1) toward the printer and the notched corner (2) to the left. 3 Angle the SIMM down about 45°, then insert the contact edge into the top socket and lift the board until it locks in place. 16 | OKI Flash SIMM Finishing the Installation 1 Position the metal plate on the housing and replace the mounting screws. 2 Open the cover and replace the side panel (tabs go in slots): you need to move the cover hinge (1) out of the way. Hardware Installation Guide: English | 17 3 Secure the panel in place with the two screws (1). 5 Reattach the PC interface cable and plug the power cord into the power outlet. 4 Close the printer cover. 18 | OKI Flash SIMM Software Utilities Overview Installation To install the Image Creator and NetFlash utilities: 1 Insert the Flash SIMM Kit CD into your CD-ROM drive. [. . . ]