User manual OKI OJ 2500

[. . . ] OKIJET ® 2500 User's Guide Every effort has been made to ensure that the information in this document is complete, accurate and up-to-date. Okidata assumes no responsibility for the results of errors beyond its control Okidata also cannot guarantee that changes in software and equipment made by other manufacturers, and referred to in this handbook, will not affect the applicability of the information in this manual. Mention of software products manufactured by other companies does not necessarily constitute endoresment by Okidata. © 1998 by Okidata First Edition, June 1998 Written and produced by the Okidata Publications Services Department. [. . . ] Press and hold for 2 to 5 seconds. 4 Control Panel Buttons Power/Reset Button With the printer on, press and release. Settings permanently stored in the printer memory are retained. Power LED Error LED Low Ink Indicators If the Power/Reset button is pressed during the print cycle, the printer will complete the current line before it stops printing. 31 4 Control panel Cartridge Change/Clean Button Resume/FF Button Function Resume printing. Print Demo page. Action If the printing has paused, press and release. Press and hold the Resume/FF button while turning the printer back on. The test page prints and the printer returns to the on-line state. Function Change ink cartridge(s). Action With the power on, press and release. (See the label inside the printer cover, or the instructions under "Replacing the Ink Cartridges" in Section 3 of this manual for instructions on changing ink cartridges). You can change cartridges during printing by pressing the Cartridge Change/Clean button, but doing so may affect the print quality. Clean the ink jet nozzles. With the power on, press and hold the button for 2 to 5 seconds. You can clean cartridges during printing by pressing the Change Cartridge/Clean button. When the printer finishes printing the current line, it ejects the sheet, and cleans the cartridge, then inserts a new sheet of paper and resumes printing where it left off. Print Test page. 32 Control Panel 4 Control Panel Indicator Lights Power LED Low Ink Indicators Condition Off Condition On Blinking Meaning Printer is on-line and ready to print. Cartridge is getting low on ink (about 10 to 15% left): make sure you have a replacement cartridge on hand. Ink cartridge is installed incorrectly Wrong brand of ink cartridge is installed. Printhead is not installed in printer. Error LED Condition On Blinking Meaning Recoverable error. Non-recoverable error: contact your service dealer (see Section 7 for information on getting service). 33 4 Control panel 34 Troubleshooting Clearing Paper Misfeeds The Error LED will be lit to indicate a misfeed. Fan the paper and reinstall it in the paper tray. 5 If the misfeeds continue, flip the paper stack over (keeping the print side facing the paper support) and press and release the Resume/FF button to continue the print job. 3. Press and release the Resume/FF button to continue the print job. 35 5 Troubleshooting Clearing Paper Jams If the Trailing Edge is Accessible If the trailing edge of the paper is accessible in the paper tray, grasp it, then press the Resume/FF button for 2 to 5 seconds. This frees up the paper so that you can pull it out. If the Trailing Edge is Not Accessible 1. If you cannot get to the trailing edge of the paper in the paper tray, remove the unused paper from the tray. To continue the print job, press the Resume/FF button. 2. Press back firmly on the green plastic tabs at either side of the paper tray until they unsnap, then remove the paper tray, observing carefully how the tray is installed. Press in on the feed plate () and insert the tray into the back of the printer at the bottom of the tray opening, then pivot the tray toward you and release the feed plate. Press and release the Resume/FF button to continue the print job. 37 5 Troubleshooting 4. Press in firmly at either end to disengage the latch tabs. Clearing Multi-Page Paper Jams If a clump of 10 or more pages has jammed in the printer, removing the paper tray will not allow sufficient clearance to extract it. Follow steps 1 through 4 under "If the Trailing Edge is Not Accessible" (see pages 36-37). [. . . ] Vendor assumes no responsibility for injury to vendee or third person party proximately caused by the product if reasonable safety procedures are not adhered to as stipulated in the MSDS. Furthermore, vendor assumes no responsibility for injury to vendee or third person party proximately caused by abnormal use of the product even if reasonable safety procedures are followed. Additionally, vendee assumes the risk of their use of the product. Reactivity Data Stability: Stable. Incompatibility: Acids. 68 Material Safety Data Sheet (MSDS) MSDS No. [. . . ]