User manual OKI MPS610C

[. . . ] MPS610c/MPS711c User's Guide 59101301 my. okidata. com Copyright Information Copyright © 2010 by Oki Data. All Rights Reserved MPS610c/MPS711c User's Guide P/N 59101301, Revision 1. 0 June, 2010 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. [. . . ] (see machine operator panel for complete list). Symbol Set IBM 437 Letter O Style Zero Character Line Pitch White Page Skip Enable/Disable Specifies the style that replaces ø (9B) and ¥ (9D) with ø (ou) and Ø (zero). Specifies the number of characters per line. Normal/ Slashed 6/8 LPI On/Off CR Function CR/CR+LF Line Length 80/136 Column Form Length TOF Position Left Margin 11/11. 7/12 inch Specifies the length of paper. 0. 0/0. 1/~1. 0 inch 0. 0/0. 1/~1. 0 inch Sets the position from the top edge of paper. Sets the amount to shift the horizontal print start position to the right. Sets the printing mode that can fit print data, equivalent to 11 inches (66 lines), in the LETTERsize printable area. SAME: Regardless of CPI, same height; DIFF: According to CPI, character heights vary. Fit to Letter Enable/Disable Text Height Same/Diff 48 ­ MPS610c/MPS711c User's Guide ITEM Color Setup Ink Simulation SETTINGS Off SWOP Euroscale Japan UCR Low Medium High EXPLANATION The machine has its own process simulation engine which simulates standard colors in the printer. If paper curl occurs in dark printing, selecting MEDIUM or LIGHT sometimes helps reduce this curl. Ordinarily, the TRC compensation function holds control for the appropriate print density; thus 100% output is not always possible. The actual print, including the TRC compensation function is limited to an appropriate area. This function is for special purposes such as specification in CMYK color reduction in PS. CMY 100% Density Enable/Disable CMYK Conversion On/Off Setting to "OFF" will simplify the conversion process of CMYK data, which will reduce the processing time. PS only 49 ­ MPS610c/MPS711c User's Guide ITEM Memory Setup Receive Buffer Size SETTINGS Auto 0. 5 megabyte 1 megabyte 2 megabyte 4 megabyte 8 megabyte 16 megabyte 32 megabyte Resource Save Auto Off 0. 5 megabyte 1 megabyte 2 megabyte 4 megabyte 8 megabyte 16 megabyte 32 megabyte EXPLANATION Sets the size of receive buffer Sets the size of resource saving area. Flash Memory Setup Initialize Execute Initializes Resident FLASH. When the Enter button is pressed, the following confirmation message appears. At this time, the request to execute FLASH initialization is put into the memory and initialization will be executed at power cycle. If Yes is selected, shutdown takes place, and FLASH is initialized at power Off/On cycle. 50 ­ MPS610c/MPS711c User's Guide ITEM SD Card Setup This item is displayed only if the SD card (option) is installed. Initialize SETTINGS Execute EXPLANATION Initializes the SD Card to the factory default setting. When this menu is executed, the following confirmation message appears. The request to execute SD Card initialization is put into the memory and initialization will be executed at the next power cycle. If Yes is selected, shutdown takes place, and the SD Card is initialized at power Off/On cycle. 51 ­ MPS610c/MPS711c User's Guide ITEM SD Card Setup (cont. ) Resize Partition SETTINGS EXPLANATION PCL nn%/ Specifies the size of partition. Common mm%/ Specifies a size by ratio to the PSll%/<Apply> whole SD Card in % (1% unit). nn, mm, ll: 1 - 98 and nn+mm+ll=100 The sizes are displayed in the partition list and can be changed by selecting the partition size to be changed. The request is put into the memory and the SD Card initialization and partition size change will be executed at next power cycle. SD Card initialization and partition size change will be executed at Power Off/On cycle. [. . . ] · Network Extension For use when your printer is connected over a TCP/IP network. Check the printer status and configuration from the Printer )Properties tab in the printer driver. · Color Swatch Utility Print a color swatch and use the indicated RGB values to set up the color(s) of your choice in your graphics/design software application. · PDF Print Direct Print pdf files without first opening them in an application. [. . . ]