User manual OKI ML 186 NETWORK CARD

[. . . ] OkiLAN 6020e® Pocket Print Server User's Guide High Performance 10/100 Base-T Ethernet Network Print Server Copyright and Trademark Information Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in products made by other manufacturers and referred to in this handbook will not affect the applicability of the information in it. T. M. , M. D. , . , and OKICOLOR T. M. , OKI Electric Industry Co. , Ltd. ; Windows, MS-DOS Reg. [. . . ] The OkiLAN 6020e interprets a subnet mask of 0. 0. 0. 0 or 255. 255. 255. 255 as no subnet mask specified. CAUTION: If you select an invalid subnet mask, you may not be able to access the OkiLAN 6020e. Default Gateway If your local network is attached to other networks, you can specify the address of your default gateway. This gateway will be selected whenever messages need to be sent to another network. The gateway address must follow the format XXX. XXX. XXX. XXX, where each XXX is a number from 0 to 255. CAUTION: If you select an invalid default gateway or the default gateway becomes unavailable, the OkiLAN 6020e may not be able to communicate with non-local networks. WINS Server If you are using WINS name resolution, set the address of the WINS Server where the System Name of the OkiLAN 6020e will be registered. Use DHCP to Locate WINS Server If you are using DHCP for IP address resolution, select this option to obtain the address of the WINS Server from the DHCP Server. IV - 26 OKI OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP Telnet/HTTP Password: Allows you to modify the current password required for Telnet or HTTP access The default password is the serial number of the OkiLAN 6020e. NetWare and NetWare Port Configuration Options For specific information on NetWare or NetWare Port options, see Section III, Novell NetWare, or select the HELP button on the bottom right of the screen. NetWare Queues Configuration Options The NetWare Queues option allows you to add bindery print queues to be serviced by first selecting each desired queue and then selecting the -> button. To have a queue print to a specific output port, select the Output Port button and then select the desired port. NetWare Queue Load Balancing Print jobs can be distributed to multiple printers on selected queues by selecting the same queue multiple times and selecting a different output port for each queue entry. OKI OkiLAN 6020e User's Guide IV - 27 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP EtherTalk Configuration Options To modify the configuration settings specific to the EtherTalk protocol such as the name and zone. For specific information on EtherTalk options, see Section VI, EtherTalk, or select the HELP button on the bottom right of the screen. Output Port Configuration Options To configure the OkiLAN 6020e output port, select the Output Port file tab. The following screen will display: Port Number Select the port number you wish to configure. Name Field Enter a descriptive name to identify the port. Language Switching Each output port can be configured to perform the following language switching options: OFF, PCL, PostScript or Automatic. Unless OFF is selected, a language switching character string will be inserted before each print job. The Printer Type selection is used to determine the actual characters required to switch your printer's language. IV - 28 OKI OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP · OFF - Print data stream will be sent directly to the output port without alteration. · PCL - Inserts the appropriate character string in front of each print job to switch the printer to the PCL print language. · PostScript - Inserts the appropriate character string in front of each print job to switch the printer to the PostScript printer language. This function examines the print job data stream and determines the required print language and inserts the appropriate character string in front of each print job to switch the printer to the appropriate printer language. Note: If you are not switching languages or the printer can switch automatically, this option should be set to OFF. Printer Type The Printer Type selection is used to determine the actual character string required for your printer. If your printer type is not listed, select Other and enter the character string for switching the printer to PCL or PostScript mode. To enter nonprintable characters, enclose the ASCII value of the character in angle brackets. For example, to enter the ESC character type: <27>. PCL Switch Sequence Enter the character string to switch the printer to the PCL print language. PostScript Switch Sequence Enter the character string to switch the printer to the PostScripti print language. Configuration Page Language Select the appropriate printer language for printing configuration pages on your printer. OKI OkiLAN 6020e User's Guide IV - 29 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP Output Type Select the appropriate baud rate. Bidirectional Printer Status Support Enable this option for enhanced status from the bidirectional printer. SNMP Configuration Options SNMP options specify which information is necessary for an SNMP manger to access the OkiLAN 6020e. The following screen will display: Note: SNMP options need to be configured only if you are managing an OkiLAN 6020e or getting system information using SNMP. Fill in the following information: System Name Enter the name of your choice. This name will identify the OkiLAN 6020e in your SNMP-based management program. IV - 30 OKI OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP System Contact Enter any information useful to a user if problems with the OkiLAN 6020e arise. System Location Enter a description of the OkiLAN 6020e location. Get Community Name This field is used to set the community name required to Get information from the print server. Note: For JetAdmin to function correctly with the OkiLAN 6020e, the SNMP Get and Set community name must be set to public. Set Community Name This field sets the community name required to Set information on the OkiLAN 6020e. Note: The OkiLAN 6020e cannot be configured without the correct Set community name. [. . . ] 2 From the Printer menu, click Printer Properties, or click the Printer Properties icon, or double-click on the selected printer. Note: Modification of printer options (print quality, page setup, paper source, etc. ) is not available for Internet FAX and non-Oki printers. VIII - 4 OKI OkiLAN 6020e User's Guide Section 8 - OkiView 32 Status The Status screen is reached from the Printer Properties menu. This screen displays descriptive information about the printer, as well as its online/offline status and the status text displayed on the printer's front panel. Network Property Page The Network Property Page is reached from the Printer Properties menu. [. . . ]